Re: [MoAccess] Motif ES USB not working
- From: "Rod Alcidonis" <roddj12@xxxxxxxxxxx>
- To: <MoAccess@xxxxxxxxxxxxx>
- Date: Sun, 9 Sep 2007 19:08:09 -0400
Hi, Bryan:
Thanks for the excellent tips. I was not aware of the different functions for
each port.
I was told that the USB connection should have afforded me with more midi
channels as oppose to using my midisport16 channels ; Then that can't be right
if I am only using port 1, though. I can only play on 16 channels on port 1. I
don't use the motif es as a controller yet -- need to learn how to do so
first. So, port 2 I will have to disable it. The only two ports I will need are
1 and 3, port 3 for my drum machine. This still would leave me with the same
amount of channels I had using my midisport, though.
Rod Alcidonis
Juris Doctor Candidate, 2009.
Roger Williams University School of Law
10 Metacom Ave., Box: 9003
Bristol, RI 02809
Cell: 718-704-4651
Home: 01-824-8685
Roddj12@xxxxxxxxxxx
----- Original Message -----
From: Bryan Smart
To: MoAccess@xxxxxxxxxxxxx
Sent: Sunday, September 09, 2007 6:51 PM
Subject: Re: [MoAccess] Motif ES USB not working
Rod, you don't want all ports enabled. This could possibly be your problem.
Motif port 1 is used for the keyboard, controllers, and for allowing Sonar to
play sounds on the Motif. This is the port that you'd get if you hooked up the
Motif to the computer using a MIDI interface and the basic MIDI in/out jacks on
the back of the Motif.
Port 2 is used by the Motif when its working in control surface mode.
Port 3 allows you to access another MIDI keyboard or module that is connected
to the MIDI in and out jacks on the back of the Motif. So, in addition to being
able to use the Motif as a MIDI device when it is connected to the computer
over either USB or man, you can also use the Motif as a single port MIDI
interface for another device.
On the Motif classic and ES, I think that ports 4, 5, and 6 let you have
direct access to the PLG cards. In this way, it is like each of the PLG cards
are their own separate MIDI module.
In Sonar, you should only enable the ports that you need. For example, you'd
never need input from anything other than ports 1 and 2. If you don't have PLG
cards, and don't chain MIDI devices off of the Motif, then only enable ports 1
and 2 for output.
Also, you should always use an audio metronome. Using a MIDI metronome is the
old school way of working. It requires that you give up one of your 16 MIDI
channels to serve as the metronome. That isn't a good idea.
Bryan
------------------------------------------------------------------------------
From: moaccess-bounce@xxxxxxxxxxxxx [mailto:moaccess-bounce@xxxxxxxxxxxxx] On
Behalf Of Damon Fibraio
Sent: Sunday, September 09, 2007 5:28 PM
To: MoAccess@xxxxxxxxxxxxx
Subject: Re: [MoAccess] Motif ES USB not working
Rod, to my knowledge, no. You should be able to just send. On all channels in
a port. Maybe try reinstalling the driver, or do a reset on the motif?
--
Damon Fibraio
screen names -- aol: dfibraio...msn dfibraio@xxxxxxxxxxxx skype: dfibraio
web sites: personal music site: http://www.keyboardguy.com. band:
http://www.queenoftheryche.com. Internet Radio station: http://www.nhbradio.com
Internet radio show every Wednesday night from 8 to 11 pm eastern
From: moaccess-bounce@xxxxxxxxxxxxx [mailto:moaccess-bounce@xxxxxxxxxxxxx] On
Behalf Of Rod Alcidonis
Sent: Sunday, September 09, 2007 1:21 PM
To: MoAccess@xxxxxxxxxxxxx
Subject: Re: [MoAccess] Motif ES USB not working
Damon:
Thanks for the info. I have done all that, though. I am quite shock as to why
only one port is working when I have done the same for all of the other ports.
That's why I hate configuring these things after a fresh install.
May I possibly have to mess with some menus to tell the keyboard to send on
all ports? Anyone know how to do that please if this may be the case?
Rod Alcidonis
Juris Doctor Candidate, 2009.
Roger Williams University School of Law
10 Metacom Ave., Box: 9003
Bristol, RI 02809
Cell: 718-704-4651
Home: 01-824-8685
Roddj12@xxxxxxxxxxx
----- Original Message -----
From: Damon Fibraio
To: MoAccess@xxxxxxxxxxxxx
Sent: Sunday, September 09, 2007 12:56 PM
Subject: Re: [MoAccess] Motif ES USB not working
OK, did you select the motif as in and out? You have to assign the midi
instrument definition to the midi port, too. Also, make sure your midi channels
are correct and put the motif into song or pattern mode.
--
Damon Fibraio
screen names -- aol: dfibraio...msn dfibraio@xxxxxxxxxxxx skype: dfibraio
web sites: personal music site: http://www.keyboardguy.com. band:
http://www.queenoftheryche.com. Internet Radio station: http://www.nhbradio.com
Internet radio show every Wednesday night from 8 to 11 pm eastern
From: moaccess-bounce@xxxxxxxxxxxxx [mailto:moaccess-bounce@xxxxxxxxxxxxx]
On Behalf Of Rod Alcidonis
Sent: Sunday, September 09, 2007 12:07 PM
To: MoAccess@xxxxxxxxxxxxx
Subject: [MoAccess] Motif ES USB not working
Hello guys:
I have downloaded the USB driver for the motif es, installed it, but I am
getting no sound. I have also followed the instructions to activate the USB on
the Motif es, but to no avail.
The Midi activity is being shown on my taskbar.
I have also installed and configured my Instrument definition for the Motif
es.
I noticed that in the midi devices dialog box, there is only one option to
select the motif es8. As for input, it appears that it only goes to motif 1-4.
Could it be that I am not receiving input sound? I was under the assumption
that by selecting the motif es only, as the only option given, it would work
for both input and output.
Please help; I desperately want to get this fix!
Thanks.
Rod Alcidonis
Juris Doctor Candidate, 2009.
Roger Williams University School of Law
10 Metacom Ave., Box: 9003
Bristol, RI 02809
Cell: 718-704-4651
Home: 01-824-8685
Roddj12@xxxxxxxxxxx
Other related posts:
