[roc-chat] Re: ROC Launch Control System
- From: Richard Dierking <richard.dierking@xxxxxxxxx>
- To: roc-chat@xxxxxxxxxxxxx
- Date: Wed, 10 Oct 2012 09:20:09 -0700
Rick is 100% correct on this. We need volunteers at every launch, and they
need direction from people that know what they are doing. Additionally,
after two or three days of camping, people tend to rush the
'demobilization' a bit. Sometimes, you have to remind yourself and others
to slow down a bit so no one gets hurt and equipment isn't damaged.
A recent example: During the last launch, someone accidentally hit one of
the light fixtures in the trailer when it was being loaded. The light
cover, florescent tube, and one of the ends of the fixture were destroyed.
I had to purchase a new fixture for $50 for the repair. What a waste
having to spend club money (your money!) on this. Occasionally, stuff gets
broken and I can handle that, but we need to be careful.
The club needs people to help manage the equipment and perhaps an equipment
committee could be created.
Richard Dierking
On Wed, Oct 10, 2012 at 2:37 AM, Rick Maschek <rickmaschek@xxxxxxxxxxx>wrote:
> From an outsiders point of view, the use of well intentioned volunteers
> for set up and break down causes a large amount of wear and tear on the
> equipment. I've seen too many times people just throw stuff in the range
> boxes, especially the pad number holders and blast shields. It takes only a
> few addition seconds to pack the boxes so things don't bang together and
> protect the plugs. Sometimes there is so much stuff crammed in the boxes
> that it gets 'pushed' in. When I pack the boxes I do so as if the contents
> were light bulbs, maybe not necessary but it doesn't hurt, and is easier to
> inspect what is in the box for next time. Same goes for the cables, I've
> seen people step backwards on the connectors or toss in the dirt. I usually
> make a large loop at the end of the cables and set the connector on the
> cable instead of on the dirt. All of these things could be done by showing
> volunteers that want to help how to do things. After having been a teacher
> for years I know that people usually do things the way they are shown
>
> Rick
>
> ------------------------------
> From: rrmagoo7@xxxxxxxxxxx
>
> To: roc-chat@xxxxxxxxxxxxx
> Subject: [roc-chat] Re: ROC Launch Control System
> Date: Tue, 9 Oct 2012 10:52:44 -0700
>
>
> Richard,
>
> One big question,
>
> Has there ever been a rocket accidentally launched due to a failure of the
> ROC Launch System?
>
> Answer: NO! All accidental launches have been caused by lack of knowledge
> of the RSO and or the Owner of the rocket. To my knowledge there has never
> been a "misfire" of the ROC Launch System since it was built in 2001.
>
> As for the layout of the launch system being rows of 6 spaced apart. This
> concept was arrived at after much thought and planning by a group of BOD
> members. Originally it was supposed to be 6 pads all with a minimum of 10
> ft. between them, original launch leads were cut at lengths of 30', 20',
> 10', 10', 20', 30',in that order, these lengths enabled the 2 pads at the
> center to be at least 10 feet apart and then the rest of the pads were
> supposed to be set up at 10 ft. intervals. These lengths have changed as
> the years have passed due to shorter leads and the people doing the set up
> not knowing the proper layout. Why do we need coils of excess wire laying
> on the ground behind the pads when if the pads were laid out properly the
> wires would be the correct length?
>
> The ROC launch system was built with Safety and the ability to supply
> 30amps of power maximum to each launch pad. It was built with the idea that
> it would last for many years with almost trouble free operation (which it
> has). The control cables have lasted as planned and would still be in good
> shape had they had the proper treatment and not been driven over by ATV's
> and Vehicles. But alas some people just can't seem to figure out that you
> shouldn't try to shove a square peg in a round hole and that is why the
> cable connectors are in the shape they are. As for the LCO control boxes we
> never had any trouble with them until the system was left out in the rain a
> couple of years ago.
>
> The funny part about all this is that TCC's new launch system (24 pads) is
> built on the same concept for it's ability to safe and arm 30amps of power
> to each pad. They also use a larger 33amp hour sealed lead acid battery so
> that they are able to launch multiple large scale rockets using high amp
> igniters simultaneously for the whole weekend without fear of the battery
> going dead.
>
> Enough for now,
>
> Ron McGough
>
> ----- Original Message -----
> *From:* Richard Dierking <richard.dierking@xxxxxxxxx>
> *To:* roc-chat@xxxxxxxxxxxxx
> *Sent:* Tuesday, October 09, 2012 9:33 AM
> *Subject:* [roc-chat] Re: ROC Launch Control System
>
> Good point. There could be a high tone for armed and continuity, and low
> tone for armed with no continuity.
>
> I still think wireless to individual pads rather than groups of pads would
> be better. For example, instead of left middle, center middle, and right
> middle, you would just have the middle row with lots of distance between
> the pads. This makes it safer for people loading rockets. Have you ever
> been loading your rocket next to someone you've never seen before prepping
> their complex rocket, and thought "I sure hope they know what their
> doing?" Or, had someones rocket CATO 6 feet from your rocket as it sits on
> the pad? Distance between pads is a good thing!
>
> I don't want a misunderstanding about what's on the table, because I see
> comments about the safety of a wireless system. If the individual pad has
> shunt and power switches, how could the rocket accidentally launch when
> being loaded? If the launch control box gives a audible and visual warning
> that the pad is in an armed condition, the person would have to be ignoring
> the warning as they were loading their rocket and switch the power on
> during this warning. If they're that stupid, they should be involved in
> another hobby like ham radio.
>
> Sorry, JK. Just wanted to see if any one's reading this stuff.
>
> Richard Dierking
> On Tue, Oct 9, 2012 at 8:20 AM, Jim - TFJ <jim@xxxxxxxxxxxxxxx> wrote:
>
> **
>
> If you’re using a processor at each group of pads, you could program the
> buzzer/siren make a different sound if continuity is lost.****
>
> ****
>
> ****
>
> Jim G.****
>
> ****
> ------------------------------
>
> *From:* roc-chat-bounce@xxxxxxxxxxxxx [mailto:
> roc-chat-bounce@xxxxxxxxxxxxx] *On Behalf Of ***Richard** Dierking
> *Sent:* Monday, October 08, 2012 9:26 AM
> *To:* **roc-chat@xxxxxxxxxxxxx**
> *Subject:* [roc-chat] Re: ROC Launch Control System****
>
> ****
>
> The most important safety feature is having the shunt/power switch
> (mechanical switch) at the pad with a visual and audible warning that the
> pad is armed. This puts the responsibility for safety back in the hands of
> the person loading their rocket.****
>
> ****
>
> I think having a continuity check at the pad is a good thing, but don't
> think the continuity check at the LCO for a high-power rocket pad is that
> important. If the rocket doesn't go when the button is pushed and there's
> continuity at the pad, it's a recycle and the igniter must be checked. If
> the rocket doesn't go and there isn't continuity, the igniter must be
> checked. So, really what's the value of having a continuity check if the
> rocket doesn't launch?****
>
> ****
>
> Regarding the battery, it shouldn't take a large battery for the
> individual launch pad controllers. We launch 6 rockets all day using a 12
> volt gel cell 7 Ah battery.****
>
> ****
>
> Regarding the front row and model rocket pads, these could still use
> cables. However, I think that some kind of digital system using Cat 5
> cable would be better. It's not expensive cable to replace if necessary,
> and a lot easier to deploy and hook up.****
>
> ****
>
> If ROC budgeted to save $2000 per year (approx $175 per launch), this
> would probably be enough money to develop a wireless system and go wireless
> for the high-power pads in approximately 3 years.****
>
> ****
>
> **Richard******
>
> On Mon, Oct 8, 2012 at 7:29 AM, **Richard** <rocket_hall@xxxxxxxxxxxxx>
> wrote:****
>
> David is this possibly a XBEE module? The XBEE modules could accomplish
> exactly what **Richard**'s dream system would need. I have some
> experience with these too. **Richard** Dierking I can put together a
> couple of concepts both "dream system" and "partial dream system" The
> biggest problem I see would be batteries(one per pad). I won't be at
> ROCtober but will be at ROCstock.
>
> **Richard** C. Hall
> TRA 11515****
>
> -----Original Message-----
> From: David Erbas-White
> Sent: Oct 7, 2012 7:14 PM
> To: roc-chat@xxxxxxxxxxxxx
> Subject: [roc-chat] Re: ROC Launch Control System ****
>
> On 10/7/2012 6:03 PM, **Richard** Dierking wrote:
>
> In my 'real life' job I'm working with some wireless systems (actually,
> using a wireless module with our own proprietary control circuitry -- but
> as the module is FCC approved, don't need to worry about that end of it).
> I have tested this system on the lakebed to over a mile, reliably. If we
> were to come up with some definitions of exactly such a 'wireless dream
> system' were to do, I could perhaps cobble something up that would be
> extensible.
>
> Effectively, the system I'm working with is a single-master,
> multiple-slave system, which would be ideal for what we're doing. To avoid
> interference from other sources, we would have to use secure encoding,
> along with timing, to ensure safety (i.e., a secure code to arm the system,
> system disarms if it either times out or loses signal from the master,
> etc.).
>
> If we design a modular system (i.e., a relay box with batteries for doing
> the actual firing, and a 'receiver section' that handles the wireless and
> intelligence, we should be good to go. Current systems (as I envision them
> using these components) would require a PC to act as the launch
> controller. If we really wanted to, we could simply build a wireless box
> that 'looks' like the current launch controller, but sends the proper
> signals via the wireless master -- but I'm just kind of thinking out loud...
> ****
>
> What might be the more difficult aspect (possibly) would be the continuity
> detection (wirelessly), as we would need to have the circuitry in the
> range-head box to 'tell' the wireless unit if continuity was present, etc.
> And this circuitry would need to work in conjunction with the current
> system of the push-button/buzzer for the pad area itself. We'd also need
> to ensure that we can handle the wider-range of igniter firing levels (like
> the new Quest igniters) with such a system..****
>
> Love to hear what other folks might think...
>
> David Erbas-White
>
> ****
>
> ****
>
> *Wireless System:*****
>
> These types of systems (particularly multi pad systems) are just being
> developed and there's not a lot of experience using them. If we had to
> obtain a new system today, I would suggest a wireless system because of the
> savings on the weight and cable cost. But we don't need a new system
> currently, so let's see what's developed over the next couple of years and
> listen to their experiences. In the meantime, we can save for a system so
> when ROC's ready, we'll have the money for a safe and reliable system.****
>
> ****
>
> For me, my 'dream system' would look something like this: A small control
> box would be located at each launch pad that would be the receiver for a
> computer based wireless system. The LCO would launch rockets using a
> computer and daylight monitor connected to a powerful (over 2,500' range)
> wireless transmitter. The pad control box would have a shunt and power
> switch controlled by the person loading the rocket and be located on a
> ground stake that would also have the pad number sign. There would be both
> audible and visual arm signal on the box and it would also have a
> connection for a larger battery if necessary (i.e. more firing amps). So,
> no central control boxes, just place the launch control box with the pad
> number sign were you want a pad, attach the launch leads with clips, and
> away you go. This would allow for any kind of spacing on rows.****
>
> ****
>
> **Richard** Dierking****
>
> ****
>
> -- ROC-Chat mailing list roc-chat@xxxxxxxxxxxxx
> //www.freelists.org/list/roc-chat ****
>
> ****
>
>
>
Other related posts:
