[torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec?
- From: "Miraglia, Walter" <Walter.Miraglia@xxxxxxxxxxx>
- To: "'torontocbm@xxxxxxxxxxxxx'" <torontocbm@xxxxxxxxxxxxx>
- Date: Sat, 23 May 2009 11:23:23 -0500
Wow thank you very much, that's a lot of info... I really appreciate it...
:o) cheers :)
----- Original Message -----
From: torontocbm-bounce@xxxxxxxxxxxxx <torontocbm-bounce@xxxxxxxxxxxxx>
To: torontocbm@xxxxxxxxxxxxx <torontocbm@xxxxxxxxxxxxx>
Sent: Sat May 23 08:49:28 2009
Subject: [torontocbm] Re: does any one know what the correct syntax for
opening a .d64 image is on sd2iec?
Miraglia, Walter wrote:
> Greed LED (LED 2) definitely shows activity when I am able to communicate
> with the SD2EIC...
> Red LED (LED 1) turns on first, then starts it's methodical on and off...
>
sd2iec defines 3 LED functions:
DIRTY/ERROR
BUSY
AUX
On the SD2IEC (the hardware), the AUX is off, and LED1 is BUSY, while
LED2 is DIRTY/ERROR.
On the uIEC 2.3 (IDE), AUX is off, LED1 is PWR (red) and LED2 is
ERROR/BUSY (green). The DIRTY function is not used.
On the uIEC 3.0 (SD), AUX is red (and is also used as PWR), and
ERROR/BUSY is GREEN.
> The firware for both is the same, on LARs version there are two leds, LED 1
> connected to PA0
> And LED 2 connected to PA1.... :) where is your one LED connected?
>
The firmware is indeed compiled from the same source code, but there are
specific changes for each hardware target (as noted above for LEDs). On
the 2.3 uIEC, the single status LED is on PE3, while on uIEC/SD (3.0),
PWR is on PG1, and ERROR/BUSY is on PG0
Other related posts:
- » [torontocbm] does any one know what the correct syntax for opening a .d64 image is on sd2iec?- Miraglia, Walter
- » [torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec?- Golan Klinger
- » [torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec?- Miraglia, Walter
- » [torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec?- Miraglia, Walter
- » [torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec?- Miraglia, Walter
- » [torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec?- Tom Luff
- » [torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec?- Miraglia, Walter
- » [torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec?- Miraglia, Walter
- » [torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec?- James Alexander
- » [torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec?- Miraglia, Walter
- » [torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec?- James Alexander
- » [torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec?- Miraglia, Walter
- » [torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec?- Jim Brain
- » [torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec?- Miraglia, Walter
- » [torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec?- Jim Brain
- » [torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec? - Miraglia, Walter
- » [torontocbm] Re: does any one know what the correct syntax for opening a .d64 image is on sd2iec?- Jeff Bourdeau