[tccrockets] Re: Attn: Brian Dalby
- From: "bkhdalb" <bkhdalb@xxxxxxxxxxx>
- To: <tccrockets@xxxxxxxxxxxxx>
- Date: Mon, 17 Oct 2011 01:29:52 -0700
hey, ben
men the suck . I wish you to see and fly same EX motor to !
Brian
From: Ben Sandoval
Sent: Friday, October 14, 2011 9:55 PM
To: tccrockets@xxxxxxxxxxxxx
Subject: [tccrockets] Re: Attn: Brian Dalby
Just my luck I won't be able to make EX - Rx day. I had hopes of maybe
finally trying to fly an EX on EX day. Guess DA 2012 is the ticket.
--- On Fri, 10/14/11, bkhdalb <bkhdalb@xxxxxxxxxxx> wrote:
From: bkhdalb <bkhdalb@xxxxxxxxxxx>
Subject: [tccrockets] Re: Attn: Brian Dalby
To: tccrockets@xxxxxxxxxxxxx
Date: Friday, October 14, 2011, 8:26 AM
right on jack
From: JACK GARIBALDI
Sent: Friday, October 14, 2011 8:13 AM
To: wlmailhtml:/mc/compose?to=tccrockets@xxxxxxxxxxxxx
Subject: [tccrockets] Re: Attn: Brian Dalby
Do It on EX day and we will treat it like a Shawn motor ( sorry Shawn
couldn't resist ) and put it at the away cell.
Jack G
----- Original Message -----
From: Jim Norton
To: wlmailhtml:/mc/compose?to=tccrockets@xxxxxxxxxxxxx
Sent: Friday, October 14, 2011 7:58 AM
Subject: [tccrockets] Re: Attn: Brian Dalby
Yes, those are C-slot grains.
-----Original Message-----
From: James Marino <wlmailhtml:/mc/compose?to=jmarino1@xxxxxxxxxxxxx>
To: tccrockets <wlmailhtml:/mc/compose?to=tccrockets@xxxxxxxxxxxxx>;
Paul M. Pittenger <wlmailhtml:/mc/compose?to=pmp42@xxxxxxxxxxx>
Sent: Fri, Oct 14, 2011 1:02 am
Subject: [tccrockets] Re: Attn: Brian Dalby
Suggest you think and consider for a while before selecting
the nozzle for something like this. Those AT 18m D loads have some seriously
small nozzle throats.
Tripling up the grains will triple the burn surface area. To
keep the Kn ratio in the realm of the realistic, a good starting place would be
to also triple the nozzle throat area. You have some geometry homework to do...
8^)
Even then... No guarantees. Might go boom. IIRC, those are
C-slot grains.
J
----- Original Message -----
From: wlmailhtml:/mc/compose?to=chvy91bowtie@xxxxxxx
To: Paul M. Pittenger ;
wlmailhtml:/mc/compose?to=tccrockets@xxxxxxxxxxxxx
Sent: Thursday, October 13, 2011 10:18 PM
Subject: [tccrockets] Re: [tccrockets] Re: Attn: Brian Dalby
No clue to be honest. Brian was talking to me at DA about wishing
he could put all three grains from an aerotech 18mm 3pk of reloads in one case.
So I said I can do that. Last night I finally got around to it. The case holds
all three grains and a delay grain for possible tracking. The forward closure
is plugged on this one but could use the delay and charge. Will it work?
Someone else will definately know better than I.
Sent from my HTC on the Now Network from Sprint!
----- Reply message -----
From: "Paul M. Pittenger"
<wlmailhtml:/mc/compose?to=pmp42@xxxxxxxxxxx>
Date: Thu, Oct 13, 2011 9:12 pm
Subject: [tccrockets] Re: Attn: Brian Dalby
To: <wlmailhtml:/mc/compose?to=tccrockets@xxxxxxxxxxxxx>
Cool, that is a pretty long 18mm... what is the max impulse range?
----- Original Message -----
From: Jack Garibaldi
To: wlmailhtml:/mc/compose?to=tccrockets@xxxxxxxxxxxxx
Sent: Thursday, October 13, 2011 8:36 PM
Subject: [tccrockets] Re: Attn: Brian Dalby
Have Rob do some sugar loads for you for testing.
Jack G
From: wlmailhtml:/mc/compose?to=tccrockets-bounce@xxxxxxxxxxxxx
[wlmailhtml:/mc/compose?to=tccrockets-bounce@xxxxxxxxxxxxx&] On Behalf Of Rob
Diehl
Sent: Thursday, October 13, 2011 7:56 PM
To: wlmailhtml:/mc/compose?to=tccrockets@xxxxxxxxxxxxx
Subject: [tccrockets] Re: Attn: Brian Dalby
Nice!
From: wlmailhtml:/mc/compose?to=tccrockets-bounce@xxxxxxxxxxxxx
wlmailhtml:/mc/compose?to=tccrockets-bounce@xxxxxxxxxxxxx] On Behalf Of
wlmailhtml:/mc/compose?to=Chvy91bowtie@xxxxxxx
Sent: Thursday, October 13, 2011 9:58 AM
To: wlmailhtml:/mc/compose?to=tccrockets@xxxxxxxxxxxxx
Subject: [tccrockets] Attn: Brian Dalby
Brian, I finally got around to machining the 18mm hardware we
talked about back at DA. Not sure if it will work but I think it looks pretty
cool. I will bring a set to October Skies for you. The shiny object in the
center is a dime for scale.
Other related posts:
