[pure-silver] Re: temp for flattening prints
- From: "Ralph W. Lambrecht" <info@xxxxxxxxxxxxxxxx>
- To: PureSilverNew <pure-silver@xxxxxxxxxxxxx>
- Date: Thu, 20 Apr 2006 00:37:16 +0200
Correct. I don't like to change the dial too much, since the dial itself has
some hysteresis, leading to inconsistent temperature settings.
Regards
Ralph W. Lambrecht
http://www.darkroomagic.com
On 2006-04-19 21:57, "Shannon Stoney" <sstoney@xxxxxxx> wrote:
>> My dry-mount temperature is 80-90C for RC and 90-100C for FB. I have to
>> state a range, because you don't get a constant temperature from a dry-mount
>> press.
>
>
> So for FB, that would be around 200 degrees Fahrenheit. That's a good
> bit hotter than Richard's temperatures for flattening.
>
> --shannon
>
>>
>>
>>
>>
>>
>> Regards
>>
>>
>>
>> Ralph W. Lambrecht
>>
>> http://www.darkroomagic.com
>>
>>
>>
>>
>>
>>
>>
>> On 2006-04-19 15:42, "Shannon Stoney" <sstoney@xxxxxxx> wrote:
>>
>>>> Shannon
>>>>
>>>> I use the same temp as for dry-mounting for 2 minutes between two pieces
>>>> of
>>>> mat-board. Then I take it out and cool it under a heavy piece of
>>>> glass for 5
>>>> minutes. Aluminum may be a better heat conductor, but glass works fine and
>>>> is easier to get get and to keep clean.
>>>
>>>
>>> What is your dry mounting temperature?
>>>
>>> --shannon
>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> Regards
>>>>
>>>>
>>>>
>>>> Ralph W. Lambrecht
>>>>
>>>> http://www.darkroomagic.com
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> On 2006-04-19 03:06, "Shannon Stoney" <sstoney@xxxxxxx> wrote:
>>>>
>>>>> I think I am going to check the temperature that that dry mount press
>>>>> I have been using gets to. It doesn't seem to get very hot to me.
>>>>> But, what is the right temperature for flattening prints?
>>>>>
>>>>> --shannon
>>>>>
>>>>>
>>>>>
>>>>> ==========================================================================
>>>>> ==
>>>>> ==
>>>>> ===============================
>>>>> To unsubscribe from this list, go to www.freelists.org and logon to your
>>>>> account (the same e-mail address and password you set-up when you
>>>>> subscribed,)
>>>>> and unsubscribe from there.
>>>>
>>>>
>>>>
>>>> ===========================================================================
>>>> ==
>>>> ================================
>>>> To unsubscribe from this list, go to www.freelists.org and logon to
>>>> your account (the same e-mail address and password you set-up when
>>>> you subscribed,) and unsubscribe from there.
>>>
>>>
>>> ============================================================================
>>> ==
>>> ===============================
>>> To unsubscribe from this list, go to www.freelists.org and logon to your
>>> account (the same e-mail address and password you set-up when you
>>> subscribed,)
>>> and unsubscribe from there.
>>
>>
>> =============================================================================
>> ================================
>> To unsubscribe from this list, go to www.freelists.org and logon to
>> your account (the same e-mail address and password you set-up when
>> you subscribed,) and unsubscribe from there.
>
> ==============================================================================
> ===============================
> To unsubscribe from this list, go to www.freelists.org and logon to your
> account (the same e-mail address and password you set-up when you subscribed,)
> and unsubscribe from there.
=============================================================================================================
To unsubscribe from this list, go to www.freelists.org and logon to your
account (the same e-mail address and password you set-up when you subscribed,)
and unsubscribe from there.
Other related posts:
