[wdmaudiodev] Re: Need help in Wave Test
- From: Gaurav Khuntale <gauravkhuntale@xxxxxxxxx>
- To: wdmaudiodev@xxxxxxxxxxxxx
I am trying to install MSVad but its not getting installed. Getting some
failures. Will update you once it got install.
Thanks.
On Wed, Feb 5, 2014 at 11:59 PM, Matthew van Eerde <
Matthew.van.Eerde@xxxxxxxxxxxxx> wrote:
> Could be a bug in portcls when calling into WaveCyclic miniports... does
> it repro on MSVad?
>
>
>
> *From:* wdmaudiodev-bounce@xxxxxxxxxxxxx [mailto:
> wdmaudiodev-bounce@xxxxxxxxxxxxx] *On Behalf Of *Gaurav Khuntale
> *Sent:* Tuesday, February 4, 2014 8:27 PM
>
> *To:* wdmaudiodev@xxxxxxxxxxxxx
> *Subject:* [wdmaudiodev] Re: Need help in Wave Test
>
>
>
> Hi Tim,
>
> No, i observed that when its paused then IDmaChannel::CopyTo function does
> not get call in my driver. So its means in paused state, no write operation
> is happening. Also as per the log file message "[ GetLastError() returned
> 21 (0x15) - The device is not ready. ]." , it seems that its returning
> with correct return status ( STATUS_DEVICE_NOT_READY ) when pin is in pause
> state and still write request comes. This is mentioned in explanation of
> IOCTL_KS_RESET_STATE on MSDN,
> http://msdn.microsoft.com/en-us/library/windows/hardware/ff560832%28v=vs.85%29.aspx.
>
>
> Thanks.
>
>
>
> On Wed, Feb 5, 2014 at 3:06 AM, Tim Roberts <timr@xxxxxxxxx> wrote:
>
> Gaurav Khuntale wrote:
> >
> > Start Case: ID 16.26:1.5: Standard Streaming\Rendering Pin Tests\Reset
> > Pin while streaming data
> > KSPIN_DATAFLOW_IN pin is currently in state KSSTATE_PAUSE; want
> > it to be in state KSSTATE_RUN
> > Setting KSPIN_DATAFLOW_IN pin to state KSSTATE_RUN
> > Position reported before issuing KSRESET_BEGIN = 121 bytes
> > KSPIN_DATAFLOW_IN pin is currently in state KSSTATE_RUN; want it
> > to be in state KSSTATE_RUN
> > Resetting Pin state: IOCTL_KS_RESET_STATE (KSRESET_BEGIN)
> > Position reported after issuing KSRESET_BEGIN = 0 bytes
> > Submitting IOCTL_KS_WRITE_STREAM IRP ...
> > GetLastError did not return ERROR_IO_PENDING even though the pin
> > is paused
>
> Looking at this again, I guess I'm a bit confused. The
> IOCTL_KS_RESET_STATE command should be handled by the port class port
> driver. I don't think it feeds down to the miniport at all.
>
> The key thing this seems to be complaining about is that your driver
> allowed a "write" to occur even though it is paused. Again, I'm not
> sure that is under your control. The MSVAD driver only checks for the
> "paused" state in a very few circumstances.
>
>
> --
> Tim Roberts, timr@xxxxxxxxx
> Providenza & Boekelheide, Inc.
>
> ******************
>
> WDMAUDIODEV addresses:
> Post message: mailto:wdmaudiodev@xxxxxxxxxxxxx
> Subscribe: mailto:wdmaudiodev-request@xxxxxxxxxxxxx?subject=subscribe
> Unsubscribe: mailto:wdmaudiodev-request@xxxxxxxxxxxxx?subject=unsubscribe
> Moderator: mailto:wdmaudiodev-moderators@xxxxxxxxxxxxx
>
> URL to WDMAUDIODEV page:
> http://www.wdmaudiodev.com/
>
>
>
Other related posts:
