[tcb] Re: air in the mc
- From: Brian Denning <i_am_cool_fred@xxxxxxxxxxx>
- To: <tcb@xxxxxxxxxxxxx>
- Date: Tue, 11 Mar 2008 10:06:04 -0500
most early bus and beetle guys cringe when i tell them how much some things
cost on a bay. i.e. the mastercylinder. another one is type IV pistons and
cylinders...ouch. oh, and beams.
Date: Tue, 11 Mar 2008 07:44:59 -0700
From: bugcollections@xxxxxxxxxxxxx
Subject: [tcb] Re: air in the mc
To: tcb@xxxxxxxxxxxxx
Brian: Just checked with Oak Hill Auto in Longview and they have a new German
ATE for $145. There phone # is 903-297-3496 if you want to give them a call.
They can UPS it to you, but by the time you paid shipping the one at Rogers
would probably be cheaper.
Brian Denning <i_am_cool_fred@xxxxxxxxxxx> wrote: every FLAPS store go to
says they can't get one for my bus. A new one cost $200 at bus-boys.com and
about 150 at roy rogers. guess i'll be going to roy rogers in the next month to
get a new one.
From: sukchew@xxxxxxxxxxxxxx
To: tcb@xxxxxxxxxxxxx
Subject: [tcb] Re: air in the mc
Date: Tue, 11 Mar 2008 07:04:37 -0500
You don't have any time.Fix your brakes NOW! If you don't the fire will
have been minor.If you don't have brake assist the mc should be around 40 bucks
at your FLAPS.I just bought one for a bug for 30 bucks. ----- Original
Message ----- From: Brian Denning To: tcb@xxxxxxxxxxxxx Sent: Tuesday,
March 11, 2008 6:35 AM Subject: [tcb] Re: air in the mc
anybod got a good new mc they'd sell me for cheap??
apparently mine is bad
i have driven the bus like this since august...how long do i have?
Date: Mon, 10 Mar 2008 19:46:08 -0700
From: bugcollections@xxxxxxxxxxxxx
Subject: [tcb] Re: air in the mc
To: tcb@xxxxxxxxxxxxx
It sounds to me like you have a leak in
the MC. Fluid going past the piston (which it is not supposed to do) which
means a new master cylinder.
Brian Denning <i_am_cool_fred@xxxxxxxxxxx> wrote: ok, the mastercylinder
has 3 lines coming out of it one that goes to the rear one for the left front
and one for the right front. at the mastercylinder i bled all air out of
it...there was lots in the line that went to the rear of the bus and some that
went to the driverside front. so i bled all the air out at the MC then i went
to the right rear. by i, i mean a friend of mine. we did the ol' tube in a
bottle of fluid trick. got some small bubbles out of the right rear, next we
went to the left rear, man oh man there were some
bubbles after we pumped it two or three times. then we went to the right
front, it took forever to get to fluid (keep in mind i have already bled
everything 4 times before this point) then we went to the driverside front. got
air.
pedal then worked but not impressive. so we decided to pressure bleed the
system at this point pump, pump pump HOLD!!! right rear spit out air twice then
solid fluid shot out like a water cannon. pump pump pump HOLD!!! left rear did
the same. moved to the right front it took 5 tries to get the final air out of
it. then we moved to the right side. fluid came out like an old man trying to
pee, slow and it dribbled for a bit. we did that for a bit and then all of the
sudden the fluid shot out so strong it hit the other side. tightened it up
the brakes are great, they don't give way but there is still a slight problem,
if i come on strong at first they work great. i even tested them and managed to
get all four
wheels to lock up, if i eas on them the pedal goes down about half way till it
works, and if i just gently push it in it still goes to the floor.
what do ya'll think? mastercylinder needs replaced or still some air hidden
somewhere? i am buying the appropriate tool from harbor freight this weekend
and will try it again but i am leaning towards a mastercylinder. like a friend
once told me "rebuilds only last so long"
> From: sukchew@xxxxxxxxxxxxxx
> To: tcb@xxxxxxxxxxxxx
> Subject: [tcb] Re: air in the mc
> Date: Mon, 10 Mar 2008 17:49:27 -0500
>
> You also can use a hand vac pump and suck the fluid thru the system so
> pressure does not have to be applied to to the master cyl.
> ----- Original Message -----
> From: "Gerald V. Livingston II" <gerald.tcb@xxxxxxxxxxxxx>
> To: <tcb@xxxxxxxxxxxxx>
> Sent: Monday, March 10, 2008 4:31 PM
> Subject: [tcb] Re: air in
the mc
>
>
> > I've used it. It only needs to be at about 10 PSI. Works GREAT. Just have
> > to make sure the reservoir stays full and pump it back up to 10PSI every
> > once in a while. Because it's forcing the fluid into the M/C at the normal
> > inlet locations it helps "grab" the air bubbles with the moving fluid and
> > pulls them out into the lines.
> >
> > Bleed the whole system in under 30 minutes with no pedal pumper helping
> > you and complaining he whole time. ;-)
> >
> > G2
> >
> > Brian Denning wrote:
> >> i'm afraid it would blow the fill line off the resevoir.
> >>
> >> > Date: Mon, 10 Mar 2008 14:50:57 -0500
> >> > From: eric@xxxxxxxxxxxxxx
> >> > To: tcb@xxxxxxxxxxxxx
> >> > Subject: [tcb] Re: air in the mc
> >> >
> >>
> Have you actually used this power bleeder?
> >> > Do they work well?
> >> >
> >> >
> >> > Gerald V. Livingston II wrote:
> >> > > Brian Denning wrote:
> >> > >> that is the concensus on the master cylinder. any tricks to
> >> bleeding
> >> > >> it with it installed? just unhook the hose and pump away or what?
> >> > >>
> >> >
> >> >> ------------------------------------------------------------------------
> >> > >> Need to know the score, the latest news, or you need your
> >> > >> Hotmail®-get your "fix". Check it out.
> >> > >> <http://www.msnmobilefix.com/Default.aspx>
> >> > >
> >> > > I've read the other replies. If it is air in the M/C then you either
> >> >
> have to pull the M/C and bench bleed it OR go ahead and take it to a
> >> > > shop that has a motorized vacuum bleeder and let them do it.
> >> > >
> >> > > You may also be able to clear it by buying and using a Motive Power
> >> > > Bleeder:
> >> > >
> >> > >
> >> <http://www.amazon.com/Air-Cooled-VW-Power-Bleeder/dp/B0002KM5LK/ref=sr_1_8?ie=UTF8&s=automotive&qid=1205174704&sr=1-8>
> >> > >
> >> > >
> >> > > That's a nice tool to have available anyway. Makes bleeding brakes
> >> EASY!
> >> > >
> >> > > Gravity bleeding won't get a bubble sitting at the top of the M/C.
> >> > >
> >> > > Gerals
> >> > >
> >> > >
> >> >
> >>
>
> >>
> >> ------------------------------------------------------------------------
> >> Shed those extra pounds with MSN and The Biggest Loser! Learn more.
> >> <http://biggestloser.msn.com/>
> >
> >
> >
> >
> > --
> > Internal Virus Database is out-of-date.
> > Checked by AVG Free Edition. Version: 7.5.516 / Virus Database:
> > 269.21.3/1308 - Release Date: 3/3/2008 10:01 AM
> >
> >
>
>
Climb to the top of the charts! Play the word scramble challenge with star
power. Play now!
Connect and share in new ways with Windows Live. Get it now!
Internal Virus Database is out-of-date.
Checked by AVG Free Edition.
Version: 7.5.516 / Virus Database: 269.21.3/1308 - Release Date: 3/3/2008 10:01
AM
Helping your favorite cause is as easy as instant messaging. You IM, we
give. Learn more.
_________________________________________________________________
Helping your favorite cause is as easy as instant messaging. You IM, we give.
http://im.live.com/Messenger/IM/Home/?source=text_hotmail_join
Other related posts:
