[PCB_FORUM] Re: ODB++ output (*.tgz) to Fab (no gerbers)
- From: "Macindoe, Gary" <Gary.Macindoe@xxxxxxxxxxxx>
- To: <icu-pcb-forum@xxxxxxxxxxxxx>
- Date: Tue, 27 Jul 2010 10:03:47 -0400
Hi Randy,
No, you can see by my "sig" that I'm now working in Boulder. So are you in
Beaverton (Tektronix)? I worked for Tektronix in Redmond, OR for 16 ½ years.
I don't know the answer to your question, we're not doing BBVs here (yet!).
Regards,
Gary MacIndoe
Senior PCB Layout Designer
Contract - Kelly Services
Covidien
EbD R&D
5920 Longbow Drive
Boulder, CO 80301
303.476.7458
www.covidien.com
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Randy Dawson
Sent: Monday, July 26, 2010 7:06 PM
To: icu-pcb-forum
Subject: [PCB_FORUM] Re: ODB++ output (*.tgz) to Fab (no gerbers)
Hi Gary,
Still in Ft. Collins?
I sent ODB++ to my board shop, Prototron while I was at Micron, a few hundred
PCBs. And I concur with Oscar, ODB is a good measure of the capabilities of a
board shop. (and their financial strength, the V in Valor stands for Very
Expensive)
Related question does an ODB++ dataset have the intelligence for blind, buried
and backdrilling?
If we set up the padstacks for HDI technology, is ODB++ suficient or do we
still need to split out separate drill files?
Randy Dawson
Tektronix
________________________________
Date: Mon, 26 Jul 2010 16:30:11 -0700
From: o.miguelino@xxxxxxxxx
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: ODB++ output (*.tgz) to Fab (no gerbers)
I have been supplying ODB++ to suppliers in Asia, Europe, and US for over a
year now. Anyway I have found that quality suppliers support ODB++ and the bad
ones do not.
Best regards,
-oscar
Oscar Miguelino
HP | Palm GBU | PSG
950 W Maude Ave | Sunnyvale | CA 94085
Confidentiality Notice: This e-mail and its contents contain information that
is proprietary and confidential to Palm, Inc. and that may also be privileged.
Any review, use, disclosure, distribution or reproduction of this email or its
contents by anyone other than an authorized recipient is prohibited and may be
unlawful. If you are not an authorized recipient, please immediately notify
me, permanently delete this message from your system and destroy any copies
thereof, including any attachments. Thank you.
-- Sent from my Palm Pre
________________________________
On Jul 26, 2010 3:56 PM, jwages <jwages@xxxxxxxxx> wrote:
I use both types. It is always good to have gerbers for comparison to the ODB++
files.
Jim S. Wages
SR PCB Layout Designer
H) 919-237-3915 C) 919-484-2963
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Macindoe, Gary
Sent: Monday, July 26, 2010 6:27 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] ODB++ output (*.tgz) to Fab (no gerbers)
Hey guys,
Has anyone been supplying only the *.tgz file (instead of gerbers, drill, ipc
etc.) to the Fab house?
If you have, have you run into any issues (besides a Fab house unable or
unwilling to use only the *.tgz file)?
Thanks for any input.
Regards,
Gary MacIndoe
Senior PCB Layout Designer
Contract - Kelly Services
Covidien
EbD R&D
5920 Longbow Drive
Boulder, CO 80301
303.476.7458
www.covidien.com
________________________________
The New Busy is not the old busy. Search, chat and e-mail from your inbox. Get
started.
<http://www.windowslive.com/campaign/thenewbusy?ocid=PID28326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_3>
Other related posts:
