Yes, in the test alpha versions with the new modes. 73, John On 24/03/2012 12:33 PM, "remi.chateauneu@xxxxxxxxx" < remi.chateauneu@xxxxxxxxx> wrote: > There's a fldigi internal queue whose size has to be increased. > There was a talk about this.? Probably, John already applied these changes > somewhere: > > <mailto:remi.chateauneu@gmail.****com <remi.chateauneu@xxxxxxxxx>>> wrote: > >> > > >> > Hi again John, > >> > > >> > Probably, a processing queue cannot be emptied quickly enough. > >> > Apart from speeding up your code, you might try these changes, they > >> may help a bit: > >> > > >> > (1) > >> > qrunner.h > >> > LOG_ERROR("qrunner: thread %" PRIdPTR " fifo full!", > GET_THREAD_ID()); > >> > Replaced by; > >> > LOG_ERROR("qrunner: thread %" PRIdPTR " fifo full at %s!", > >> GET_THREAD_ID(),typeid(F).****name() ); > >> > > >> > So that we will see with which function it happens. > >> > > >> > (2) > >> > src/qrunner/qrunner.cxx: > >> > #define FIFO_SIZE 2048 > >> > Replaced by; > >> > #define FIFO_SIZE 8192 > >> > > >> > So that the queue will be bigger and might leave enough time for > >> processing. > >> > > >> > (3) > >> > ./configure --enable-optimizations=native > >> > > >> > This should produce a code with better instructions. > >> > > >> > (4) > >> > In m4/opt.m4 > >> > > >> > OPT_CFLAGS="-O2 -ffast-math -finline-functions" > >> > > >> > Replaced by > >> > > >> > OPT_CFLAGS="-O3 -ffast-math -finline-functions" > >> > > >> > As well, the code should be slightly faster. > >> > > >> > Hope this helps. > >> > > >> > Cheers > >> > > >> > Remi > >> > > > > Le 23.03.2012 19:36, Eric Davenport a écrit : > >> I have some more information that may be important or a guidance to all. >> >> JPSKMail ran for a number of hours today and then FLDIGI froze and >> created a 250Meg Status_Log.TXT >> >> Most of it was filled with the following. >> >> I: apply: RSID: PSK250R @ 1044 Hz >> I: apply: RSID: PSK250R @ 1044 Hz >> I: ParseMode: ARQ new modem set to PSK250R >> I: ParseMode: ARQ new modem set to PSK250R >> I: apply: RSID: PSK250R @ 1050 Hz >> I: ParseMode: ARQ new modem set to PSK250R >> I: ParseMode: ARQ new modem set to PSK250R >> I: apply: RSID: PSK250R @ 1050 Hz >> I: apply: RSID: PSK250R @ 1044 Hz >> I: apply: RSID: BPSK250 @ 1050 Hz >> I: apply: RSID: PSK250R @ 1044 Hz >> E: request: qrunner: thread 0 fifo full! >> E: request: qrunner: thread 0 fifo full! >> E: request: qrunner: thread 0 fifo full! >> E: request: qrunner: thread 0 fifo full! >> E: request: qrunner: thread 0 fifo full! >> E: request: qrunner: thread 0 fifo full! >> E: request: qrunner: thread 0 fifo full! >> E: request: qrunner: thread 0 fifo full! >> E: request: qrunner: thread 0 fifo full! >> and this went of till I stopped it at 250 megs. >> >> Hope this helps us. >> >> >> > >