If your sldb file did not have anything that correctly represents the system
hosting, especially no CP's or Workstations in that file, then your sysdef is
not correct.
The sldb file comes directly off the commit diskette and is built according the
Sysdef stations that have been assigned to each other and smon hosting.
So sysdef is not right
-----Original Message-----
From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] On ;
Behalf Of Joseph M. Riccardi
Sent: Friday, September 23, 2016 12:10 PM
To: foxboro@xxxxxxxxxxxxx
Subject: Re: [foxboro] Windows NT AW70 V6.4 SysDef changes and commit
Just for the record, I attempted to rerun the commit procedure and at the 1st
prompt for a diskette I get the message "The current package blah, blah, blah
has been successfully installed in a previous installation. Do you want to set
this package to Day 0 status?" I assume "No" but nothing makes sense. Ditto
for other diskettes. The packages are marked as "DONE" in the IIF.cur but they
are not showing up in the System after rebooting.
Of the changes, the CIO_Config/CSA move appears to be working but the System
Monitor and CP host changes are not despite the IIF.cur marked as "DONE".
Sooooooooo...
The setup log.txt shows the following errors: *****(There are no Release
Level Diskettes, only (4) Revision Level Diskettes 11001-11004. Are they
the same? Does it indicate I have a bad set of Release/Revision Level
Diskettes? Where can I get replacements?)*****
INFO:C:\TEMP\_ISTMP9.DIR\tar.exe xf \\.\A: ./OS1CS ./ACSA7 ./AADM7 ./AW70
INFO: Tar returned error on disk set: Release Level Diskette.
INFO:C:\TEMP\_ISTMP9.DIR\tar.exe xf \\.\A: ./OS1CS ./ACSA7 ./AADM7 ./AW70
INFO: Tar returned error on disk set: Release Level Diskette.
INFO:C:\TEMP\_ISTMP9.DIR\tar.exe xf \\.\A: ./OS1CS ./ACSA7 ./AADM7 ./AW70
INFO: Tar returned error on disk set: Release Level Diskette.
INFO:C:\TEMP\_ISTMP9.DIR\tar.exe xf \\.\A: ./OS1CS ./ACSA7 ./AADM7 ./AW70
INFO: Tar returned error on disk set: Release Level Diskette.
INFO:C:\TEMP\_ISTMP9.DIR\tar.exe xf \\.\A: ./OS1CS ./ACSA7 ./AADM7 ./AW70
INFO: Tar returned error on disk set: Release Level Diskette.
INFO:C:\TEMP\_ISTMP9.DIR\tar.exe xf \\.\A: ./OS1CS ./ACSA7 ./AADM7 ./AW70
INFO: Tar returned error on disk set: Release Level Diskette.
INFO:C:\TEMP\_ISTMP9.DIR\tar.exe xf \\.\A: ./OS1CS ./ACSA7 ./AADM7 ./AW70
INFO: Tar returned error on disk set: Release Level Diskette.
INFO:C:\TEMP\_ISTMP9.DIR\tar.exe xf \\.\A: ./OS1CS ./ACSA7 ./AADM7 ./AW70
INFO: Tar returned error on disk set: Release Level Diskette.
Joseph M. Riccardi
386-451-7607 Cell
Joe@xxxxxxxxxxxxx
"To give real service you must add something that cannot be bought or measured
with money; and that is sincerity and integrity." - Donald A. Adams
-----Original Message-----
From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] On ;
Behalf Of Joseph M. Riccardi
Sent: Thursday, September 22, 2016 5:49 PM
To: foxboro@xxxxxxxxxxxxx
Subject: Re: [foxboro] Windows NT AW70 V6.4 SysDef changes and commit
Russ and Terry, et al... Gents, please don't give up on me yet. I think I am
close...
-----Original Message-----
From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] On ;
Behalf Of Joseph M. Riccardi
Sent: Thursday, September 22, 2016 11:21 AM
To: foxboro@xxxxxxxxxxxxx
Subject: Re: [foxboro] Windows NT AW70 V6.4 SysDef changes and commit
Russ and Terry,
Thanks for the help and suggestions. I will address both of your comments
below...
1st I would like to review what I see at this point...
- I double checked the SysDef configuration and everything looks good,
just as I changed them. The System Monitor was reassigned to the new AW70, the
CPs are all hosted by the new AW70, the old AW70 is gone, and all of the
checked and verified columns are "Yes" with a modified date of yesterday.
:-)
- The d:/usr/fox/sp/IIF.pkg file shows the new AW70, all CPs/FBMs that were
re-hosted, and ASMON7 (System Monitor?) as NOTYET. ;-( I see a number of the
standard software packages as DONE, including AICC7 (ICC?). During the commit
process I inserted all of the appropriate diskettes (i.e., System Monitor, ICC,
CP60, etc.) when prompted and all installed without errors.
At this point my conclusion is that the SysDef process and the move CSA process
was successful, but the commit process failed miserably. Why?
Status...
- When I call up the System Management Display the System Monitor is not
shown, getting error "System Monitor not responding". That makes sense since
ASMON7 = NOTYET.
- When I open the CIO_Config it appears that all of the Compounds are listed
but when I pick one I get "CSA Error - CSgetcmpd Failed". That makes sense
since CSA move OK but AICC7 = NOTYET.
- If I select the CIO_Station_Config there are no CPs listed.
- All of the /usr/fox/sp/*lns files look correct.
- sldb is a new file to me but it only shows the Stations hosting volumes.
What should it show?
- All CPs are empty and not even on line.
- I moved the Checkpoint files from the old AW70 to the new one to reboot them
as soon as I resolve the commit process issues. Or I was hoping to do a
Load_All from the Save_All files I created and then checkpoint them so the
Checkpoint files are up to date.
It sure looks to me like I am close if I can figure out why the commit process
failed. Any ideas? Or just do it again?
Thanks
Joseph M. Riccardi
386-451-7607 Cell
Joe@xxxxxxxxxxxxx
"To give real service you must add something that cannot be bought or measured
with money; and that is sincerity and integrity." - Donald A. Adams
_________________________________________________________________________
This mailing list is neither sponsored nor endorsed by Schneider Electric
(formerly The Foxboro Company). Use the info you obtain here at your own
risks. See the disclaimer at www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
______________________________________________________________________
*** Confidentiality Notice: This e-mail, including any associated or attached
files, is intended solely for the individual or entity to which it is
addressed. This e-mail is confidential and may well also be legally privileged.
If you have received it in error, you are on notice of its status. Please
notify the sender immediately by reply e-mail and then delete this message from
your system. Please do not copy it or use it for any purposes, or disclose its
contents to any other person.
_________________________________________________________________________
This mailing list is neither sponsored nor endorsed by Schneider Electric
(formerly The Foxboro Company). Use the info you obtain here at your own
risks. See the disclaimer at www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
