[TechAssist] Re: Toshiba VCR M-684C doesn't record channel pre-programmed in.
- From: "Wilfred Blakey" <wblakey@xxxxxxxxxxxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Thu, 19 Dec 2002 11:52:08 -0500
You sound like you need a "ROUND TUIT", the same as myself and likely many
others whose equipment needs attention.
Blakey TV
Kirkland Lake,Ont.,Canada
----- Original Message -----
From: <gulftech@xxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Thursday, December 19, 2002 12:58 PM
Subject: [TechAssist] Re: Toshiba VCR M-684C doesn't record channel
pre-programmed in.
>
> Gary,
>
> I have (at home) a Toshiba M761 that develops amnestia if power is
> removed for more that a few minutes. Used to hold for hours. There's a
> large value cap for memory hold. I think it's C660. Still haven't
> changed it, but will get it done eventually.
>
> Hope this helps,
>
>
> Ken Smith
> Gulf Technical Services
> 3034 Gulf Breeze Parkway
> Gulf Breeze, FL 32563
> 850-934-8324 (Voice) 850-932-0819 (Fax)
>
>
> On Thu, 19 Dec 2002 01:27:20 -0500 Gary McCartney <gary@xxxxxxxxxxx>
> writes:
> >
> > I believe I have this channel problem figured out. Turned out that
> > the
> > channels needed to be autoprogrammed into memory, then when I set the
> > timer to record, it did record the channel I had it set for. I must
> > have
> > missed going channel up/down to tune in stations, but thanks to a
> > couple
> > of techs replies, it reminded me. I normally use direct enter
> > because I
> > only get a handful of channels on the antenna. Only thing is, I don't
> > know yet if the VCR has a problem with losing it's auto-programmed
> > channel memory. Is it normal for these models to lose the channel
> > memory
> > with a short loss of AC power, or does it take a prolonged period of
> > time? I will try the unit out one more time after being unplugged,
> > before I send it home.
> >
> >
> >
> > Gary McCartney
> >
> > McCartney Electronics
> > 7134 Fife Rd, RR 7
> > Guelph Ontario Canada N1H 6J4
> > Fax: (519)821-1530
> > email: gary (at) number63.ca
> >
> >
> >
> >
> >
> > teltek2 wrote:
> > >
> > > This sounds like a bad micro, never ran across it myself, but this
> > may be
> > > one customer you would want to send to Wal-Mart, and do him a
> > favor. Brain
> > > surgery on VCR's is not profitable these days. ;-)
> > >
> > > -Ed
> > > Tel-Tek Electronics
> > > Ontario-Canada
> > >
> > > teltek2@xxxxxxxxxxxx
> > > ----- Original Message -----
> > > From: "J Silverman" <greentron@xxxxxxxxxxxxxxxx>
> > > To: <techassist@xxxxxxxxxxxxx>
> > > Sent: Wednesday, December 18, 2002 4:14 PM
> > > Subject: [TechAssist] Re: Toshiba VCR M-684C doesn't record channel
> > > pre-programmed in.
> > >
> > > >
> > > > Got that the first time! When the vcr is time recording does the
> > display
> > > > indicate the vcr tuner channel?
> > > > Jerry Silverman
> > > > Greentron Inc
> > > > 4 Newland Ave
> > > > Greenville SC 29609
> > > > 864 232 3889
> > > > Fax 271 2080
> > > > mailto:greentron@xxxxxxx
> > > > ----- Original Message -----
> > > > From: "Gary McCartney" <gary@xxxxxxxxxxx>
> > > > To: <techassist@xxxxxxxxxxxxx>
> > > > Sent: Wednesday, December 18, 2002 1:49 AM
> > > > Subject: [TechAssist] Re: Toshiba VCR M-684C doesn't record
> > channel
> > > > pre-programmed in.
> > > >
> > > >
> > > > >
> > > > > Ok, I'll try to explain again.
> > > > >
> > > > > The VCR does not record the channel I pre-program it to
> > record, but
> > > > > rather just snow shows up on playback (and no sound). I have
> > only tried
> > > > > channels 13 or below so it is not a CATV/antenna setting
> > problem. When I
> > > > > record manually, it records the channel I have the VCR set to
> > and plays
> > > > > it back fine. When I press record, the TV/VCR light in the VCR
> > display
> > > > > indicates VCR. When I set the timer to come on and record, the
> > VCR will
> > > > > automatically turn on in TV mode and it does not change to VCR
> > mode. The
> > > > > picture on the TV (while recording) shows the channel which is
> > shown
> > > > > when the VCR is in TV mode, in my case it shows picture of
> > channel 3.
> > > > > When I play back this recording, all I get is snow and no
> > sound. So it
> > > > > seems as though the tuner does not tune when timer recording
> > happens.
> > > > > When manual recording happens, the tuner tunes in the chosen
> > station
> > > > > fine.
> > > > >
> > > > > I have posted a picture of the on screen graphics for my timer
> > settings.
> > > > > Note that it is set to record channel 11. The record speed is
> > not shown
> > > > > in the pic because that flashes and the camers snapped the
> > shot when the
> > > > > speed was not visible. After I set this up, I press "program"
> > button as
> > > > > per instruction book, then turn VCR off and wait until it
> > automatically
> > > > > turns on.
> > > > >
> > > > > http://www.number63.ca/setting.jpg
> > > > >
> > > > > I hope this clarifies any confusion that my previous posts may
> > have
> > > > > caused.
> > > > >
> > > > >
> > > > >
> > > > > Gary McCartney
> > > > >
> > > > > McCartney Electronics
> > > > > 7134 Fife Rd, RR 7
> > > > > Guelph Ontario Canada N1H 6J4
> > > > > Fax: (519)821-1530
> > > > > email: gary (at) number63.ca
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > > C&W Electronics wrote:
> > > > > >
> > > > > > Gary,
> > > > > > My experience with VCR recording, is that the when the VCR
> > is in the
> > > > record
> > > > > > mode, it records the channel selected on the VCR, regardless
> > of the
> > > > position
> > > > > > of the tv/vcr switch. If this were not the case, you would
> > not be able
> > > > to
> > > > > > watch one channel and record another one.
> > > > > >
> > > > > > You should be able to prove this by recording manually with
> > the front
> > > > > > buttons or the remote. Turn the vcr on, select tv with the
> > tv/vcr
> > > switch
> > > > and
> > > > > > press record.
> > > > > >
> > > > > > I think I am reading your post properly.
> > > > > >
> > > > > > Good luck,
> > > > > > Paul W
> > > > > > C&W Electronics
> > > > > > Azle Texas
> > > > > >
> > > > > > ----- Original Message -----
> > > > > > From: "Gary McCartney" <gary@xxxxxxxxxxx>
> > > > > > To: <techassist@xxxxxxxxxxxxx>
> > > > > > Sent: Tuesday, December 17, 2002 3:14 PM
> > > > > > Subject: [TechAssist] Toshiba VCR M-684C doesn't record
> > channel
> > > > > > pre-programmed in.
> > > > > >
> > > > > > >
> > > > > > > This Toshiba VCR M-684C will record manually, no problem.
> > The
> > > problem
> > > > is
> > > > > > > with pre-programmed recording. It doesn't matter what
> > channel I set
> > > > the
> > > > > > > unit to record from when the timer turns on the machine,
> > the unit
> > > > always
> > > > > > > comes on in TV mode (as in TV/VCR choice) instead of VCR
> > mode, and
> > > > > > > thereby doesn't record what is wanted.
> > > > > > >
> > > > > > > Is there a specific known fix for this? I don't want to
> > spend much
> > > > time
> > > > > > > on it. Already removed circuit board and soldered power
> > supply and
> > > > > > > checked ESR of caps.
> > > > > > >
> > > > > > > If there is no known fix, would it be possible to force
> > the VCR to
> > > > turn
> > > > > > > on in VCR mode rather than TV mode? I could add a toggle
> > switch on
> > > the
> > > > > > > front panel to engage or disengage this. I'm thinking of
> > one of the
> > > > pins
> > > > > > > on the tuner might go high or low when TV/VCR button is
> > pressed. If
> > > I
> > > > > > > add a switch with a pull-up resistor maybe that would
> > work. I'd
> > > rather
> > > > > > > have the proper fix if anyone knows it and it doesn't
> > invlove
> > > > replacing
> > > > > > > the microprocessor IC.
> > > > > > >
> > > > > > >
> > > > > > > Thanks for any help.
> > > > > > > --
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > > Gary McCartney
> > > > > > >
> > > > > > > McCartney Electronics
> > > > > > > 7134 Fife Rd, RR 7
> > > > > > > Guelph Ontario Canada N1H 6J4
> > > > > > > Fax: (519)821-1530
> > > > > > > email: gary (at) number63.ca
> > > > > > >
> > > > > > > ------------------------------------------
> > > > > > > Submit A Repair Tip For Everyone Here:
> > > > > > > http://www.tech-assist.org/secure/tip/main.html
> > > > > > > ------------------------------------------
> > > > > > > To REMOVE your email address, click here:
> > > > > > > http://www.tech-assist.org/unsubb.html
> > > > > > > To CHANGE your email address, click here:
> > > > > > > http://www.techassist.net/forms/change.html
> > > > > > >
> > > > > > ------------------------------------------
> > > > > > Submit A Repair Tip For Everyone Here:
> > > > > > http://www.tech-assist.org/secure/tip/main.html
> > > > > > ------------------------------------------
> > > > > > To REMOVE your email address, click here:
> > > > > > http://www.tech-assist.org/unsubb.html
> > > > > > To CHANGE your email address, click here:
> > > > > > http://www.techassist.net/forms/change.html
> > > > >
> > > > > --
> > > > >
> > > > > ------------------------------------------
> > > > > Submit A Repair Tip For Everyone Here:
> > > > > http://www.tech-assist.org/secure/tip/main.html
> > > > > ------------------------------------------
> > > > > To REMOVE your email address, click here:
> > > > > http://www.tech-assist.org/unsubb.html
> > > > > To CHANGE your email address, click here:
> > > > > http://www.techassist.net/forms/change.html
> > > > >
> > > > >
> > > >
> > > > ------------------------------------------
> > > > Submit A Repair Tip For Everyone Here:
> > > > http://www.tech-assist.org/secure/tip/main.html
> > > > ------------------------------------------
> > > > To REMOVE your email address, click here:
> > > > http://www.tech-assist.org/unsubb.html
> > > > To CHANGE your email address, click here:
> > > > http://www.techassist.net/forms/change.html
> > > >
> > > >
> > >
> > > ------------------------------------------
> > > Submit A Repair Tip For Everyone Here:
> > > http://www.tech-assist.org/secure/tip/main.html
> > > ------------------------------------------
> > > To REMOVE your email address, click here:
> > > http://www.tech-assist.org/unsubb.html
> > > To CHANGE your email address, click here:
> > > http://www.techassist.net/forms/change.html
> >
> > --
> >
> > ------------------------------------------
> > Submit A Repair Tip For Everyone Here:
> > http://www.tech-assist.org/secure/tip/main.html
> > ------------------------------------------
> > To REMOVE your email address, click here:
> > http://www.tech-assist.org/unsubb.html
> > To CHANGE your email address, click here:
> > http://www.techassist.net/forms/change.html
> >
> >
>
>
> ________________________________________________________________
> Sign Up for Juno Platinum Internet Access Today
> Only $9.95 per month!
> Visit www.juno.com
> ------------------------------------------
> Submit A Repair Tip For Everyone Here:
> http://www.tech-assist.org/secure/tip/main.html
> ------------------------------------------
> To REMOVE your email address, click here:
> http://www.tech-assist.org/unsubb.html
> To CHANGE your email address, click here:
> http://www.techassist.net/forms/change.html
>
------------------------------------------
Submit A Repair Tip For Everyone Here:
http://www.tech-assist.org/secure/tip/main.html
------------------------------------------
To REMOVE your email address, click here:
http://www.tech-assist.org/unsubb.html
To CHANGE your email address, click here:
http://www.techassist.net/forms/change.html
Other related posts:
