Got that the first time! When the vcr is time recording does the display indicate the vcr tuner channel? Jerry Silverman Greentron Inc 4 Newland Ave Greenville SC 29609 864 232 3889 Fax 271 2080 mailto:greentron@xxxxxxx ----- Original Message ----- From: "Gary McCartney" <gary@xxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Wednesday, December 18, 2002 1:49 AM Subject: [TechAssist] Re: Toshiba VCR M-684C doesn't record channel pre-programmed in. > > Ok, I'll try to explain again. > > The VCR does not record the channel I pre-program it to record, but > rather just snow shows up on playback (and no sound). I have only tried > channels 13 or below so it is not a CATV/antenna setting problem. When I > record manually, it records the channel I have the VCR set to and plays > it back fine. When I press record, the TV/VCR light in the VCR display > indicates VCR. When I set the timer to come on and record, the VCR will > automatically turn on in TV mode and it does not change to VCR mode. The > picture on the TV (while recording) shows the channel which is shown > when the VCR is in TV mode, in my case it shows picture of channel 3. > When I play back this recording, all I get is snow and no sound. So it > seems as though the tuner does not tune when timer recording happens. > When manual recording happens, the tuner tunes in the chosen station > fine. > > I have posted a picture of the on screen graphics for my timer settings. > Note that it is set to record channel 11. The record speed is not shown > in the pic because that flashes and the camers snapped the shot when the > speed was not visible. After I set this up, I press "program" button as > per instruction book, then turn VCR off and wait until it automatically > turns on. > > http://www.number63.ca/setting.jpg > > I hope this clarifies any confusion that my previous posts may have > caused. > > > > Gary McCartney > > McCartney Electronics > 7134 Fife Rd, RR 7 > Guelph Ontario Canada N1H 6J4 > Fax: (519)821-1530 > email: gary (at) number63.ca > > > > > > > > C&W Electronics wrote: > > > > Gary, > > My experience with VCR recording, is that the when the VCR is in the record > > mode, it records the channel selected on the VCR, regardless of the position > > of the tv/vcr switch. If this were not the case, you would not be able to > > watch one channel and record another one. > > > > You should be able to prove this by recording manually with the front > > buttons or the remote. Turn the vcr on, select tv with the tv/vcr switch and > > press record. > > > > I think I am reading your post properly. > > > > Good luck, > > Paul W > > C&W Electronics > > Azle Texas > > > > ----- Original Message ----- > > From: "Gary McCartney" <gary@xxxxxxxxxxx> > > To: <techassist@xxxxxxxxxxxxx> > > Sent: Tuesday, December 17, 2002 3:14 PM > > Subject: [TechAssist] Toshiba VCR M-684C doesn't record channel > > pre-programmed in. > > > > > > > > This Toshiba VCR M-684C will record manually, no problem. The problem is > > > with pre-programmed recording. It doesn't matter what channel I set the > > > unit to record from when the timer turns on the machine, the unit always > > > comes on in TV mode (as in TV/VCR choice) instead of VCR mode, and > > > thereby doesn't record what is wanted. > > > > > > Is there a specific known fix for this? I don't want to spend much time > > > on it. Already removed circuit board and soldered power supply and > > > checked ESR of caps. > > > > > > If there is no known fix, would it be possible to force the VCR to turn > > > on in VCR mode rather than TV mode? I could add a toggle switch on the > > > front panel to engage or disengage this. I'm thinking of one of the pins > > > on the tuner might go high or low when TV/VCR button is pressed. If I > > > add a switch with a pull-up resistor maybe that would work. I'd rather > > > have the proper fix if anyone knows it and it doesn't invlove replacing > > > the microprocessor IC. > > > > > > > > > Thanks for any help. > > > -- > > > > > > > > > > > > > > > Gary McCartney > > > > > > McCartney Electronics > > > 7134 Fife Rd, RR 7 > > > Guelph Ontario Canada N1H 6J4 > > > Fax: (519)821-1530 > > > email: gary (at) number63.ca > > > > > > ------------------------------------------ > > > Submit A Repair Tip For Everyone Here: > > > http://www.tech-assist.org/secure/tip/main.html > > > ------------------------------------------ > > > To REMOVE your email address, click here: > > > http://www.tech-assist.org/unsubb.html > > > To CHANGE your email address, click here: > > > http://www.techassist.net/forms/change.html > > > > > ------------------------------------------ > > Submit A Repair Tip For Everyone Here: > > http://www.tech-assist.org/secure/tip/main.html > > ------------------------------------------ > > To REMOVE your email address, click here: > > http://www.tech-assist.org/unsubb.html > > To CHANGE your email address, click here: > > http://www.techassist.net/forms/change.html > > -- > > ------------------------------------------ > Submit A Repair Tip For Everyone Here: > http://www.tech-assist.org/secure/tip/main.html > ------------------------------------------ > To REMOVE your email address, click here: > http://www.tech-assist.org/unsubb.html > To CHANGE your email address, click here: > http://www.techassist.net/forms/change.html > > ------------------------------------------ Submit A Repair Tip For Everyone Here: http://www.tech-assist.org/secure/tip/main.html ------------------------------------------ To REMOVE your email address, click here: http://www.tech-assist.org/unsubb.html To CHANGE your email address, click here: http://www.techassist.net/forms/change.html