sounds like a drive problem with the conv. gen board (dcu) or bad yoke. I have not seen any yoke problems with these sets Robert tvservice@xxxxxxxxxxxxx H & H Electronics Inc http://supertek.igniteinc.biz ----- Original Message ----- From: "markbrock" <markbrock@xxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Wednesday, October 26, 2005 5:58 AM Subject: [TechAssist] Re: Akai red convergence > thanks guys, I did what you said, and I usually change em both myself, > but not on these that have one for vert and one for Horz,, unless both are > bad, anyway, swapped, em, problem did not follow the IC, changed them > both with new sanyo's, ( thinking it was a marriage thing ? ) { they are > just audio amps } same, checked all the resistors again, still the same, > the one stk gets way to hot to be normal, if left on for 5 minutes will > probably burn up, I've added heat sink while I was trying to determine if I > could get it closer to alignment, still got pretty hot, it is being way > over driven, can the DCU have this out of adjustment enough to cause it > to draw more current ? I guess so, > > Brock Electronics > R.R.4 box 237 > 5208 cr.3385 > Independence Ks. 67301 > 620-331-0235 > fax 331-7191 > > markbrock@xxxxxxxxxxxxx > Zenith*Philips*Peavey*Fender*Crate > we work on all brands,makes,models > of anything that plugs in the wall > ----- Original Message ----- > From: "markbrock" <markbrock@xxxxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Tuesday, October 25, 2005 6:20 AM > Subject: [TechAssist] Akai red convergence > > > > model PTH5498 > > this set came in with bad convergence, all three bowed down from top, > the > > fuse under ICZ104 was open, so I changed this STK392-040, now the > > convergence is ok for green and blue but red is actually worse and the ic > > gets hot, fuse still in tack but red convergence is so far out that there > > is not way to correct, this is a sanyo ic and I know there is some > > discussion about after market stk's, the printing is smaller. I didn't > > follow the thread on this discussion because I always tell em, original > > only. and its original sanyo ? not sure what that means, but since the > > red and blue horz and vert are ok I'm suspecting something else ? one of > > these is ic's control vert and one is horz if I remember correctly, I > > replaced only the one with the bad fuse ? anyone ? .. help. red yoke ? > > how do I test it -vs- replacement. > > brock > > > > > > > > Brock Electronics > > R.R.4 box 237 > > 5208 cr.3385 > > Independence Ks. 67301 > > 620-331-0235 > > fax 331-7191 > > > > markbrock@xxxxxxxxxxxxx > > Zenith*Philips*Peavey*Fender*Crate > > we work on all brands,makes,models > > of anything that plugs in the wall > > > > -------------------------------------------------------------------------- > --- > > This Email List is accessible to the general public through search > engines. Remove: http://www.tech-assist.org/remove.htm > > Set Vacation > mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation > > Lost Password: http://www.tech-assist.org and select "Login Problems?". > > Email Archives: //www.freelists.org/archives/techassist/ > > -------------------------------------------------------------------------- --- > This Email List is accessible to the general public through search engines. Remove: http://www.tech-assist.org/remove.htm > Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation > Lost Password: http://www.tech-assist.org and select "Login Problems?". > Email Archives: //www.freelists.org/archives/techassist/ ----------------------------------------------------------------------------- This Email List is accessible to the general public through search engines. Remove: http://www.tech-assist.org/remove.htm Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/