[SI-LIST] Re: [!! SPAM] Re: 6 layers stackup
- From: Istvan Novak <istvan.novak@xxxxxxxxxxx>
- To: Joel Brown <joel@xxxxxxxxxx>
- Date: Wed, 12 Mar 2008 09:05:06 -0400
Joel,
Yes, I meant two discrete components: low-ESR MLCC and a discrete
resistor in series.On medium and large boards still today the smallest
part your assembly house might want to handle is the 0402 size, but if
you make the layout to minimize the total loop size (nothing fancy,
nothing exotic), you can achieve the resonance reduction shown in the
published paper (measured on production boards).
Interesting that you mention single pins. The R-C termination can be
used for both area decoupling and single-pin decoupling. For area
decoupling you start with the characteristic impedance of the plane
shape and you match that value with the parallel equivalent of all of
the Rs placed on the plane. For very small puddles or single-pin strip
feeds you can safely use a single capacitor or R-C.
Regards,
Istvan Novak
SUN Microsystems
Joel Brown wrote:
> Istvan,
>
> Just a few qusetions regarding your comments:
>
> By adding discrete resistors do you mean add them in series with normal low
> ESR ceramic capacitors?
> If 0402 packages are used for both would the inductance be sufficiently low?
> I assume the higher ESR bypassing should be done as percentage of the total
> bypassing and should not be used to bypass local IC power pins?
>
> Thanks - Joel
>
>
>
> -----Original Message-----
> From: si-list-bounce@xxxxxxxxxxxxx [mailto:si-list-bounce@xxxxxxxxxxxxx] On
> Behalf Of Istvan Novak
> Sent: Tuesday, March 11, 2008 6:04 AM
> To: steve weir
> Cc: Joel Brown; leeritchey@xxxxxxxxxxxxx; 'Scott McMorrow'; 'QU Perry';
> si-list@xxxxxxxxxxxxx
> Subject: [SI-LIST] Re: [!! SPAM] Re: 6 layers stackup
>
> Joel,
>
> Just a few late comments to the thread (I was on vacation):
>
> - setting the resistance to dampen resonances is a useful thing to reduce
> worst-case transient noise and EMI risk. For regular MLCCs this usually
> requires ESR values higher than what we get with a typical manufacturing
> process today.
>
> - in ceramic capacitors the required resistance can be created either by a
> smart internal construction (see the TDK announcement pointed out on the
> thread), or by adding resistance externally such as printed resistors (such
> as Sanmina's annual ring resistor) or by adding discrete resistor pieces
>
> - as it was mentioned, inductance is crucial: whether the resistance is
> added inside the MLCC or externally, we should not add too much inductance
> as it would defeat the purpose. Fortunately each of the above three
> approaches can be implemented with sufficiently low inductance.
>
> - for implementation options and simulated measured results you can see some
> of the published papers on the topic. See for instance:
> "Overview of Some Options to Create Low-Q Controlled-ESR Bypass Capacitors"
> and "History of Controlled-ESR Capacitors at SUN" in TecForum TF-MP3
> "Controlled-ESR Bypass Capacitors Have Arrived" on
> http://home.att.net/~istvan.novak/papers.html
>
> Finally another comment on inductance: instead of setting the resistance to
> the optimum value, sufficiently low overall inductance of the bypass
> capacitors can also be used to reduce/eliminate resonances. This is the
> rational (knowingly or unknowingly) behind the approach Charles mentioned
> (sprinkling the board with a lot of capacitors) and this is
> the reason why lower inductance parts are always a welcome help.
> However, from a design point of view we need to keep in mind that using a
> low cumulative inductance instead of the optimum resistance comes with a
> price: either the low-inductance parts are more expensive, or the
> low-inductance parts require more vias, or simply we need more parts.
> Of course setting the resistance to the proper value has its own price tag
> as well, so eventually the design engineer has to make the decision which
> solution fits bets his/her requirements. Typically in low-density and
> low-cost systems adding more capacitors works well; in high-density and/or
> high-performance systems selecting PDN components with the proper resistance
> becomes more attractive.
>
> Regards,
>
> Istvan novak
> SUN Microsystems
>
>
> steve weir wrote:
>
>> Joel, controlled / high ESR caps are rare birds. Istvan has been
>> championing them for years nd some parts have been made. If you are
>> prepared to buy 100,000,000 at a shot you might get somewhere w/ the
>> manufacturers. But right now, most are running their lines to
>> capacity w/ commodity parts.
>>
>> Regards,
>>
>>
>> Steve.
>> Joel Brown wrote:
>>
>>
>>> While we are all talking about bypass caps, I just got done reading a
>>> book by Bruce Archambeault called "PCB Design for Real-World EMI
>>> Control". In the book there is a chapter on bypassing and it shows
>>> measurements from actual test boards. In one case, a certain percentage
>>>
> of the caps are "high ESR"
>
>>> which seems to result in substantial damping (reduction) of the
>>>
> resonances.
>
>>> The high ESR caps are described as ceramic capacitors with a series
>>> resistor built into the package, I have been unable to find such a
>>> part. Has anybody found a benefit to this approach and a source for high
>>>
> ESR capacitors?
>
>>> Thanks - Joel
>>>
>>>
>>>
>>>
------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
or to administer your membership from a web page, go to:
//www.freelists.org/webpage/si-list
For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
List technical documents are available at:
http://www.si-list.net
List archives are viewable at:
//www.freelists.org/archives/si-list
or at our remote archives:
http://groups.yahoo.com/group/si-list/messages
Old (prior to June 6, 2001) list archives are viewable at:
http://www.qsl.net/wb6tpu
Other related posts:
