[PCB_FORUM] Re: Low on available memory, please exit the program.

Has anyone here been able to install RHEL 4 on T61P?


To get back to my initial post, I removed a couple of programs from the
config - many are still there, cannot be removed.
Next thing will be to compare the running programs/tasks on my pc with
another pc.
Cadence says it is my PC, not Allegro.

I'll keep on digging.

Julian 

-----Original Message-----
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Mike Finczak
Sent: Friday, February 22, 2008 8:55 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Low on available memory, please exit the
program.

Julian and Richard,

        Tom's Hardware recently had an article that explained why
        only 3 Gig of ram is addressable on windows 32 bit systems.

        http://www.tomshardware.com/2008/02/15/vista_workshop/
 

Regards,
       Mike Finczak
       CopperCAD Design
       www.CopperCAD.com
       905-488-8958



 

________________________________

From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of
ricmar@xxxxxxxxxxx
Sent: Friday, February 22, 2008 11:45 AM
To: icu-pcb-forum@xxxxxxxxxxxxx; icu-pcb-forum@xxxxxxxxxxxxx; Walter
Boese Jr.
Cc: Walter Boese Jr.
Subject: [PCB_FORUM] Re: Low on available memory, please exit the
program.


I have been informed XP will run 4 GIG but reports it incorrectly as 3
GIG.
 
I have it on my other site and a 3RD Party Utility (Avanquest) reports
it as 4 GIG.
 
Richard E Marion
 
-------------- Original message --------------
From: "Walter Boese Jr." <walterb@xxxxxxx> 

> Not that this is your problem, but for info purposes. 
> Windows XP cannot address 4gig of memory. 
> There is a 3gig switch, but we have found that to be problematic. 
> 
> The only way to address 4gig is with Windows XP Pro 64bit and Cadence 
> does not support 64bit Windows at this time.
> 
> Walter Boese Jr. 
> SGI
> 
> 
> Julian Ungureanu (jungurea) wrote: 
> > 
> > I thought I post this here before I open a case with Cadence. 
> > I get this message when updating DRCs. 
> > The brd file is ~100 Mb. 
> > T61P, 2.2 GHz, 4 Gb RAM, Windoze XP Any ideas why?
> > 
> > 
> > Thanks,
> > Julian U. 
> > 
> > 
> 
> --
> 
> 
> Walter Boese, Jr. 
> wa lterb@ sgi.com
> 
> -----------------------------------------------------------
> To subscribe/unsubscribe: 
> Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
> with a subject of subscribe or unsubscribe
> 
> To view the archives of this list go to 
> http://www.freelists.org/archives/icu-pcb-forum/
> 
> Problems or Questions: 
> Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
> -----------------------------------------------------------

-----------------------------------------------------------
To subscribe/unsubscribe: 
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe

To view the archives of this list go to
http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------
-----------------------------------------------------------
To subscribe/unsubscribe: 
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe

To view the archives of this list go to 
http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------

Other related posts: