Re: [foxboro] Peer to Peer connection good but not updating
- From: "Boulay, Russ" <Russ.Boulay@xxxxxxxxxxxx>
- To: "foxboro@xxxxxxxxxxxxx" <foxboro@xxxxxxxxxxxxx>
- Date: Mon, 27 Aug 2012 15:47:16 -0400
A similar issue can also occur if blocks that have peer to peer connections are
copied and pasted.
The index that was saved from original block to it's peer is carried over in
the copy and if the CP is checkpointed before the copied block has been edited
with it's unique connections...issues can occur.
-----Original Message-----
From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] On
Behalf Of tjvandew@xxxxxxxxx
Sent: Monday, August 27, 2012 2:17 PM
To: foxboro@xxxxxxxxxxxxx
Subject: Re: [foxboro] Peer to Peer connection good but not updating
We experienced similar peer to peer OM table issues and finally figured out
that it was associated with trying to change a peer to peer sink connection
from one variable to another in the same session. Seemed to be if the source
block was deleted in CP1 before removing the sink connection to the deleted
block in CP2 and then going to the sink block in Cp2 and changing the bad
connection to a valid connection. This could cause the OM table to shift
references. The sink block connection looked ok but was pointed to the wrong
source variable in the OM table. Very insideous. Once the OM table was hosed
the only way we found to fix it was a sink CP reboot. Our work around was:
Always remove the sink connection 1st
Then checkpoint sink CP
Remove the old source block from the source CP Checkpoint the source CP Add the
new sink connection Checkpoint the sink CP Tom Sent from my Verizon Wireless
BlackBerry
-----Original Message-----
From: Michael Kessler <mkessler@xxxxxxxxxxxxx>
Sender: foxboro-bounce@xxxxxxxxxxxxx
Date: Mon, 27 Aug 2012 12:46:10
To: foxboro<foxboro@xxxxxxxxxxxxx>
Reply-To: foxboro@xxxxxxxxxxxxx
Subject: [foxboro] Peer to Peer connection good but not updating
I have some peer to peer connections between calcA blocks in ZCP's that are not
updating. (XXX.BO01 > YYY.BI01) I've deleted/undeleted the blocks, with no
success. Deleting the source block does not turn the sink point Cyan which
should normally be the case.
I am able to see the status of the source using omget.
I suspect corrupt OM lists. Will a re-boot clear these up or is a CP
initialize/loadall required?
Anyone experienced this type of problem?
mk
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process Systems
(formerly The Foxboro Company). Use the info you obtain here at your own risks.
Read http://www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process Systems
(formerly The Foxboro Company). Use the info you obtain here at your own risks.
Read http://www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
*** Confidentiality Notice: This e-mail, including any associated or attached
files, is intended solely for the individual or entity to which it is
addressed. This e-mail is confidential and may well also be legally privileged.
If you have received it in error, you are on notice of its status. Please
notify the sender immediately by reply e-mail and then delete this message from
your system. Please do not copy it or use it for any purposes, or disclose its
contents to any other person. This email comes from a division of the Invensys
Group, owned by Invensys plc, which is a company registered in England and
Wales with its registered office at 3rd Floor, 40 Grosvenor Place, London, SW1X
7AW (Registered number 166023). For a list of European legal entities within
the Invensys Group, please go to http://www.invensys.com/en/legal/default.aspx.
You may contact Invensys plc on +44 (0)20 3155 1200 or e-mail
reception@xxxxxxxxxxxxx This e-mail and any attachments thereto may be subject
to the terms of any agreements between Invensys (and/or its subsidiaries and
affiliates) and the recipient (and/or its subsidiaries and affiliates).
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
Other related posts:
