Sorry, already tried that. This micro times has been a problem for me for since I started trying to use it almost two years ago. Thanks again, you all have jogged my memory on some things I had forgotten. Frank ----- Original Message ----- From: "Kevin A. Wasik" <kwasik@xxxxxxxxx> To: <amayausers@xxxxxxxxxxxxxxxx> Sent: Thursday, April 15, 2004 9:13 PM Subject: Re: [amayausers] micro times > Hey Frank > > Note: you can tighten the bobbin little more it should be fine for > the runs you are doing. Then you can reset the bobbin back to Amaya specs. > Kevin Wasik. > Melco Field Tech. > > > frank davis wrote: > > >Thanks Kevin. I tried 40 and 30. It did help, but I still have a few > >bobbin threads showing. I'll keep playing. > >Frank > >----- Original Message ----- > >From: "Kevin A. Wasik" <kwasik@xxxxxxxxx> > >To: <amayausers@xxxxxxxxxxxxxxxx> > >Sent: Wednesday, April 14, 2004 11:07 PM > >Subject: Re: [amayausers] micro times > > > > > > > > > >>40 works good. Don't forget to reset it back to 50 after you are done. > >>Kevin Wasik. > >>Melco Field Tech. > >> > >> > >>frank davis wrote: > >> > >> > >> > >>>No, that's one I haven't tried. Actually I forgot about it. I'll give > >>> > >>> > >it a > > > > > >>>shot. Thanks Janel. > >>>Frank > >>>----- Original Message ----- > >>>From: "Janel Harris" <janel@xxxxxxxxxxxxxx> > >>>To: <amayausers@xxxxxxxxxxxxxxxx> > >>>Sent: Wednesday, April 14, 2004 9:22 PM > >>>Subject: RE: [amayausers] micro times > >>> > >>> > >>> > >>> > >>> > >>> > >>>>Frank, > >>>> > >>>>Have you tried lowering the column feed? > >>>> > >>>>Janel Harris > >>>>Dimensional Designs > >>>>http://www.dimdesigns.com > >>>>Contract Digitizer > >>>>Melco On-Site Trainer > >>>> > >>>> > >>>>-----Original Message----- > >>>>From: frank davis [mailto:fadavis@xxxxxxxxxxxx] > >>>>Sent: Wednesday, April 14, 2004 5:45 PM > >>>>To: Amayausers@xxxxxxxxxxxxxxxx > >>>>Subject: [amayausers] micro times > >>>> > >>>>Does anyone but me have trouble with micro times. > >>>>I'm using a 70/10 sharp needle on poplin. The lettering is .26'' and > >>>>set to specs. Lettering looks good except for the white bobbin thread > >>>>that gets pulled up through several times per letter. I've tried > >>>>everything I can think of; material thickness, bobbin tension speed, > >>>>pull comp, ect. Does anyone else have this problem? Just wondered if > >>>>someone can suggest something I'm missing. The bobbin thread in red > >>>>lettering doesn't look that great. > >>>>Thanks, > >>>>Frank > >>>>Force Ten > >>>> > >>>> > >>>>--------------------------------------------------------------------- > >>>>To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx > >>>>For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx > >>>> > >>>> > >>>> > >>>> > >>>> > >>>> > >>> > >>>--------------------------------------------------------------------- > >>>To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx > >>>For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx > >>> > >>> > >>> > >>> > >>> > >>> > >>--------------------------------------------------------------------- > >>To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx > >>For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx > >> > >> > >> > >> > > > > > > > >--------------------------------------------------------------------- > >To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx > >For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx > > > > > > > > > --------------------------------------------------------------------- To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx