[amayausers] Re: micro times

Kevin,
Is Amaya specs calling for the 2" to 4" drop for
bobbin tension still I remember it was stated one
way then changed early on when they first came out.
What do you suggest/ cause mine changes constantly especially
after 3/4 of the bobbin is gone.
Has anyone tried the magnetic bobbins? they are supposed to maintain
consistent tension through the whole bobbin.
Just wondering.
Thanks in advance!
Ron Vinyard
Owner / Graphic Designer
Body Cover / Magic Stitches
420  S.W. "H" Street
Grants Pass, OR 97526-2532

1-888-435-0176
1-541-471-1504
Fax 541-471-0427
www.bodycoverdesign.com


----- Original Message ----- 
From: "Kevin A. Wasik" <kwasik@xxxxxxxxx>
To: <amayausers@xxxxxxxxxxxxxxxx>
Sent: Thursday, April 15, 2004 6:13 PM
Subject: Re: [amayausers] micro times


> Hey Frank
>
> Note: you can tighten the bobbin little more it should be fine for
> the runs you are doing. Then you can reset the bobbin back to Amaya specs.
> Kevin Wasik.
> Melco Field Tech.
>
>
> frank davis wrote:
>
> >Thanks Kevin.  I tried 40 and 30.  It did help, but I still have a few
> >bobbin threads showing.  I'll keep playing.
> >Frank
> >----- Original Message ----- 
> >From: "Kevin A. Wasik" <kwasik@xxxxxxxxx>
> >To: <amayausers@xxxxxxxxxxxxxxxx>
> >Sent: Wednesday, April 14, 2004 11:07 PM
> >Subject: Re: [amayausers] micro times
> >
> >
> >
> >
> >>40 works good. Don't forget to reset it back to 50 after you are done.
> >>Kevin Wasik.
> >>Melco Field Tech.
> >>
> >>
> >>frank davis wrote:
> >>
> >>
> >>
> >>>No, that's one I haven't tried.  Actually I forgot about it.  I'll give
> >>>
> >>>
> >it a
> >
> >
> >>>shot. Thanks Janel.
> >>>Frank
> >>>----- Original Message ----- 
> >>>From: "Janel Harris" <janel@xxxxxxxxxxxxxx>
> >>>To: <amayausers@xxxxxxxxxxxxxxxx>
> >>>Sent: Wednesday, April 14, 2004 9:22 PM
> >>>Subject: RE: [amayausers] micro times
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>>Frank,
> >>>>
> >>>>Have you tried lowering the column feed?
> >>>>
> >>>>Janel Harris
> >>>>Dimensional Designs
> >>>>http://www.dimdesigns.com
> >>>>Contract Digitizer
> >>>>Melco On-Site Trainer
> >>>>
> >>>>
> >>>>-----Original Message-----
> >>>>From: frank davis [mailto:fadavis@xxxxxxxxxxxx]
> >>>>Sent: Wednesday, April 14, 2004 5:45 PM
> >>>>To: Amayausers@xxxxxxxxxxxxxxxx
> >>>>Subject: [amayausers] micro times
> >>>>
> >>>>Does anyone but me have trouble with micro times.
> >>>>I'm using a 70/10 sharp needle on poplin.  The lettering is .26'' and
> >>>>set to specs.  Lettering looks good except for the white bobbin thread
> >>>>that gets pulled up through several times per letter.  I've tried
> >>>>everything I can think of; material thickness, bobbin tension speed,
> >>>>pull comp, ect.  Does anyone else have this problem?   Just wondered
if
> >>>>someone can suggest something I'm missing.  The bobbin thread in red
> >>>>lettering doesn't look that great.
> >>>>Thanks,
> >>>>Frank
> >>>>Force Ten
> >>>>
> >>>>
> >>>>---------------------------------------------------------------------
> >>>>To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx
> >>>>For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>
> >>>---------------------------------------------------------------------
> >>>To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx
> >>>For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>
> >>---------------------------------------------------------------------
> >>To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx
> >>For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx
> >>
> >>
> >>
> >>
> >
> >
> >
> >---------------------------------------------------------------------
> >To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx
> >For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx
> >
> >
> >
> >
>



---------------------------------------------------------------------
To unsubscribe, e-mail: amayausers-unsubscribe@xxxxxxxxxxxxxxxx
For additional commands, e-mail: amayausers-help@xxxxxxxxxxxxxxxx

Other related posts: