there is a vertical pulse on vertical output, has anyone worked on one of these sets who could tell me if what the b+ is supposed to be the manual calls for 140v, i have 129v might be mistake in manual.if not thats my problem i guess. al marquardt ampm@xxxxxxx ----- Original Message ----- From: "Lewis Wetzel" <crsjax@xxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Thursday, November 29, 2001 6:39 AM Subject: [TechAssist] Re: magnovox ts2575 25f800 chassis > > If the vertical is missing it will shut down. If there > is a bad vertical signal out of the A/V processor > change that. I have had several bad in this way. > Lewis > --- al m <ampm@xxxxxxx> wrote: > > > > won't start . degause relay clicks one then a couple > > seconds later 5 or six > > more times. have momentary horizontal and vertical, > > but the vertical pulse > > is missing on the micro. it comes off pin 6 of > > vertical ic, goes thru what > > parst list says is a 33v zener then to a transistor. > > the puls is only 10 > > volts so i don't think it's going to get to the > > micro. don't know if that's > > the problem or if the regulator is the problem.the > > pulse would probably be > > bigger if the right voltage was there. > > al marquardt > > ampm@xxxxxxx > > ----- Original Message ----- > > From: "Phillip R. Hull" <phil245@xxxxxxxxxxxxx> > > To: <techassist@xxxxxxxxxxxxx> > > Sent: Wednesday, November 28, 2001 1:15 PM > > Subject: [TechAssist] Re: magnovox ts2575 25f800 > > chassis > > > > > > > > > > You didn't say whats wrong with unit. > > > Phillip R Hull > > > phil245@xxxxxxxxxxxxx > > > ----- Original Message ----- > > > From: "al m" <ampm@xxxxxxx> > > > To: <techassist@xxxxxxxxxxxxx> > > > Sent: Wednesday, November 28, 2001 1:23 PM > > > Subject: [TechAssist] magnovox ts2575 25f800 > > chassis > > > > > > > > > > > > > > i'm stuck on this one. manual calls for 140v on > > main output on > > > regulator.i > > > > got 129v checked all outputs for caps and diodes > > regulator has correct > > > > voltage on every pin. manual says turn down ac > > voltage and check > > > > outputs,same thing did anyone see this before > > the troubleshooting guide > > is > > > > vague on what to do, it doesn't tell what to > > check if the voltages are > > > wrong > > > > only if they're not there. any tricks would be > > appreciated been on this > > a > > > > long time and am in the same spot duh!!!!! > > > > al marquardt > > > > ampm@xxxxxxx > > > > > > > > > > > > ================================= > > > > Help make your TechAssist database better! > > > > Submit your fixes here: > > http://circuitwork.com/techassist/tip/#tips > > > > ================================= > > > > To UNSUBSCRIBE your email address, click here: > > > > > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > > > > > > > > > > ================================= > > > Help make your TechAssist database better! > > > Submit your fixes here: > > http://circuitwork.com/techassist/tip/#tips > > > ================================= > > > To UNSUBSCRIBE your email address, click here: > > > > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > > > > > > > > > > > ================================= > > Help make your TechAssist database better! > > Submit your fixes here: > > http://circuitwork.com/techassist/tip/#tips > > ================================= > > To UNSUBSCRIBE your email address, click here: > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > __________________________________________________ > Do You Yahoo!? > Yahoo! GeoCities - quick and easy web site hosting, just $8.95/month. > http://geocities.yahoo.com/ps/info1 > ================================= > Help make your TechAssist database better! > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > ================================= > To UNSUBSCRIBE your email address, click here: > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > ================================= Help make your TechAssist database better! Submit your fixes here: http://circuitwork.com/techassist/tip/#tips ================================= To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe