[TechAssist] Re: JVC VCR HR-VP639U
- From: Edward Gaidies <teltek@xxxxxxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Wed, 02 Jan 2002 20:40:45 -0500
Thanks Bill..Will post outcome.
-Ed-
>
> Ed,
>
> I have seen a few of the IR Diodes go bad on these. (You know the one in the
> middle.)
>
> I have also seen the prism's get warped or really dusty.
>
> Just a couple of thoughts.
>
> Good luck, God Bless, Happy Holidays
> Bill McFarland
> DMC Electronics
>
> ----- Original Message -----
> From: Tel-Tek Electronics <teltek@xxxxxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Wednesday, January 02, 2002 2:47 PM
> Subject: [TechAssist] Re: JVC VCR HR-VP639U
>
>
>>
>> Joe;
>> That could well be the problem, I'll give iti a shot.
>> Thanks.
>>
>> -Ed-
>> teltek@xxxxxxxxxxx
>> TEL-TEK ELECTRONICS.
>>
>>
>>
>>
>>
>> ----- Original Message -----
>> From: "Tech / 2002" <joe872@xxxxxxxxx>
>> To: <techassist@xxxxxxxxxxxxx>
>> Sent: Wednesday, January 02, 2002 4:28 PM
>> Subject: [TechAssist] Re: JVC VCR HR-VP639U
>>
>>
>>>
>>>
>>> -Ed-
>>> suggestion to try: Remove load carriage assembly, clean everything
>>> thoroughly including mode switch. With assembly removed, plug unit in
>>> and power up, make sure all mechanisms return to home base, if not, do
>>> it manually. Manually put loading carriage in home base position.
>>> Reassemble and try, may have been out of time. "joe"
>>> joe872@xxxxxxxxx
>>>
>>> Sender: techassist-bounce@xxxxxxxxxxxxx From: teltek@xxxxxxxxxxx
>>> (Tel-Tek=A0Electronics) Date: Wed, Jan 2, 2002, 3:56pm To:
>>> techassist@xxxxxxxxxxxxx (AAAA TECH-ASSIST) Subject: [TechAssist] JVC
>>> VCR HR-VP639U Reply=A0to: techassist@xxxxxxxxxxxxx
>>> Anyone spend any time oin these as far as "no Loading" of cassette. Have
>>> 2 identical models here, and VCR will not accept tape. Since I have 2
>>> here, maybe someone has run across one of these at some time, and
>>> actually fixed the problem, and made a note on the fix. Display is on,
>>> and if I complete the load, manually, seems to work Play, rewind, FF.
>>> But then will not unload the tape.
>>> Thanks;
>>> -Ed-
>>> teltek@xxxxxxxxxxx
>>> TEL-TEK ELECTRONICS.
>>> ------------------------------------------
>>> Help make your TechAssist database better! Submit your fixes here:
>>> http://circuitwork.com/techassist/tip/#tips
>>> ------------------------------------------
>>> To UNSUBSCRIBE your email address, click here:
>>> mailto:techassist-request@xxxxxxxxxxxxx?subject=3Dunsubscribe Or send a
>>> BLANK email with unsubscribe in the SUBJECT field to the address above.
>>>
>>> ------------------------------------------
>>> Help make your TechAssist database better!
>>> Submit your fixes here: http://circuitwork.com/techassist/tip/#tips
>>> ------------------------------------------
>>> To UNSUBSCRIBE your email address, click here:
>>> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
>>> Or send a BLANK email with unsubscribe in the
>>> SUBJECT field to the address above.
>>>
>>>
>>
>> ------------------------------------------
>> Help make your TechAssist database better!
>> Submit your fixes here: http://circuitwork.com/techassist/tip/#tips
>> ------------------------------------------
>> To UNSUBSCRIBE your email address, click here:
>> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
>> Or send a BLANK email with unsubscribe in the
>> SUBJECT field to the address above.
>>
>
> ------------------------------------------
> Help make your TechAssist database better!
> Submit your fixes here: http://circuitwork.com/techassist/tip/#tips
> ------------------------------------------
> To UNSUBSCRIBE your email address, click here:
> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
> Or send a BLANK email with unsubscribe in the
> SUBJECT field to the address above.
>
--
From: Ed Gaidies
teltek@xxxxxxxxxxx
Tel-Tek Electronics
------------------------------------------
Help make your TechAssist database better!
Submit your fixes here: http://circuitwork.com/techassist/tip/#tips
------------------------------------------
To UNSUBSCRIBE your email address, click here:
mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe
Or send a BLANK email with unsubscribe in the
SUBJECT field to the address above.
Other related posts:
