[PCB_FORUM] Re: Very Slow Allegro v. 16.3
- From: "Dickoff, Diane J" <diane.j.dickoff@xxxxxxxxx>
- To: "icu-pcb-forum@xxxxxxxxxxxxx" <icu-pcb-forum@xxxxxxxxxxxxx>
- Date: Tue, 5 Apr 2011 12:37:08 -0700
If you disable your dynamic shapes it still happens?
-----Original Message-----
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Mark Salberg
Sent: Tuesday, April 05, 2011 12:18 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Very Slow Allegro v. 16.3
Diane and Charles,
Thanks for your replies.
I added NORAT property to main pwrs and gnds.
It Didn't make any difference if schematic and Constraint Manager were
open or not. (But I have them both closed down)
I have never used Autosilk, but set all params to none.
Still having the same problem.
Thanks,
Mark
On 4/5/2011 3:05 PM, JCharles TEYSSIER wrote:
> Hello Mark,
>
> i do not use 16.3 (still use 15.7 and a few 16.2).
> But here are some tricks:
> - In autosilk parameters all set to "none": no need to calculate each
> time a via is moved
> - rats on "big" nets (ex.: gnd) should be disabled : calculation of
> ratsnet is time consuming
>
> I don't think it will be a big improve , but small + small + small can
> be big at the end...
>
> Jean-Charles
>
> Mark Salberg a écrit :
>> Hello,
>> I was wondering if anyone there would have any tricks to speed up
>> Allegro.
>> I am editing a board with quite a few Constraints in the V.16.3 CM.
>> Whenever I slide a trace, move a via or any mod, it hangs up for 30
>> sec each time.
>> I have tried changing global shapes params from smooth to rough and
>> even disabled.
>> Short of turning off On-Line DRC, which I do not want to do.
>> Many DRC's to clean up.
>>
>>
>> Mark
>> -----------------------------------------------------------
>> To subscribe/unsubscribe: Send a message to
>> icu-pcb-forum-request@xxxxxxxxxxxxx
>> with a subject of subscribe or unsubscribe
>>
>> To view the archives of this list go to
>> //www.freelists.org/archives/icu-pcb-forum/
>>
>> Problems or Questions:
>> Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
>> -----------------------------------------------------------
>>
>>
> -----------------------------------------------------------
> To subscribe/unsubscribe: Send a message to
> icu-pcb-forum-request@xxxxxxxxxxxxx
> with a subject of subscribe or unsubscribe
>
> To view the archives of this list go to
> //www.freelists.org/archives/icu-pcb-forum/
>
> Problems or Questions:
> Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
> -----------------------------------------------------------
-----------------------------------------------------------
To subscribe/unsubscribe:
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe
To view the archives of this list go to
//www.freelists.org/archives/icu-pcb-forum/
Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------
-----------------------------------------------------------
To subscribe/unsubscribe:
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe
To view the archives of this list go to
//www.freelists.org/archives/icu-pcb-forum/
Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------
Other related posts:
