[amayausers] Re: Dead in the water
- From: "Lee or Terri Hoover" <lhoover2@xxxxxxxxxxxxxxxx>
- To: <amayausers@xxxxxxxxxxxxx>
- Date: Thu, 18 May 2006 21:01:49 -0500
A couple of thoughts --
Check the bobbin casing, take out the bobbin, clean the case with a =
business
card under the spring, blow canned air through the bobbin,
Double check that you are putting the bobbin in the bobbin case the =
correct
direction.
Using a flashlight inspect the area of the arm where the bobbin goes, =
using
the flashlight sometimes it will reflect the light differently so that =
you
can see some thread that need to be cleaned out. Check behind the =
bobbin
case area also.
On the thread that is not picking up, check to make sure the needle is =
not
in backwards.
Make sure the needle plate is centered.
The manual can give you specifics on all the above much better than I =
can.
If it's any consulation, I've had to "correct" all the above problems. =
:)
Terri
Embroidery Creations
-----Original Message-----
From: amayausers-bounce@xxxxxxxxxxxxx
[mailto:amayausers-bounce@xxxxxxxxxxxxx] On Behalf Of Steve Griswold
Sent: Thursday, May 18, 2006 8:12 PM
To: amayausers@xxxxxxxxxxxxx
Subject: [amayausers] Dead in the water
Hi,
2 hours and still can not get my Amaya to sew more than 3 seconds.
Here are my stats:
=20
Machine: 2 weeks old Amaya XT.
Designs: Has done maybe 4-5 all with thread breaks, bobbin breaks, =
needle
breaks.
Material: Polo shirt with two layers of backing in 5.25" hoop
=20
Issue:
Tried Needle head #1, sews maybe 5 seconds and thread or bobbin break.
After this happened about 10 times the needle broke. replaced needle. =
now
the tread just comes out of the needle hole. Does not seem to catch the
bobbin. Tried playing with the bobbin tension, replaced bobbin tread =
with
new bobbin, and no luck.
Tried needle head #8, same issue, bobbin and thread breaks, then after =
maybe
8 times the needle broke. =20
Tried: =20
Replaced Thread (New ARC thread poly)
Replaced needles (1 and 8) and turn 5 degrees to the right. (75/11 BP =
in
all slots)
Checked tread path
Put in new bobbin
Cleaned bobbin case
Adjusted bobbin tension, (looser, slightly tighter) instead bobbin =
until
it clicked and left 2" of bobbin hanging out to the right. Looks like a
spider slowing going down if you hold it in your hand. placed in so it
looks like a #9 and unwinds clockwise.
=20
Adjusted pressure foot (3 up from all the way down, it is just a hair =
about
the shirt fabric)
Centered needle- removed needle plate, centered and tighted.
Oiled hook and spun.
Blew out the need hook area, checked for thread mess.
ActiFeed set to 5 and also tried 6
Any ideas?
Thanks,
Steve
Atlanta GA
=20
=20
=20
=09
---------------------------------
Ring'em or ping'em. Make PC-to-phone calls as low as 1=A2/min with =
Yahoo!
Messenger with Voice.
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=20
The AmayaUsers Mailing List
Website: http://www.amayausers.com
Discussion Board: http://www.amayausers.com/boards
Subscribe/Unsubscribe: http://www.amayausers.com/list
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=20
===========================================================
The AmayaUsers Mailing List
Website: http://www.amayausers.com
Discussion Board: http://www.amayausers.com/boards
Subscribe/Unsubscribe: http://www.amayausers.com/list
===========================================================
Other related posts:
