I have done it that way also... The only thing I have not done yet is to take the EEprom out of the circuit...and will be doing that now too.... Bill Sorensen New Life Video & Audio billans@xxxxxxxxxxxx - - - - - - - - - - - - - - - - - - - ----- Original Message ----- From: "Barry Thompson" <barrystv@xxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Tuesday, July 23, 2002 10:55 AM Subject: [TechAssist] Re: Questions on hooking up Chipper checker > > Bill the 5 volts must be applied to the eprom first before you put the pst > cable into the interface box anyway that's how its done on the 195/97 and > the 203. Barry. > Barrys TV > barrystv@xxxxxxx > 613 224 3406 > fax 613 723 9670 > 0ttawa,Canada > ----- Original Message ----- > From: "Bill S" <billans@xxxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Tuesday, July 23, 2002 5:58 PM > Subject: [TechAssist] Re: Questions on hooking up Chipper checker > > > > > > Do you mean to say if it says there is no communication to go and reset > the > > eeprom on the top of the program? > > Thanks > > Bill Sorensen > > New Life Video & Audio > > billans@xxxxxxxxxxxx > > - - - - - - - - - - - - - - - - - - - > > > > ----- Original Message ----- > > From: "Bruce Tiedeman" <btied@xxxxxxxxxxxx> > > To: <techassist@xxxxxxxxxxxxx> > > Sent: Tuesday, July 23, 2002 9:54 AM > > Subject: [TechAssist] Re: Questions on hooking up Chipper checker > > > > > > > > > > I have not done many myself but have managed. You have to select chassis > > and > > > highlight the chassis number , then you hook up power to the EPROM. Next > > hit > > > the button again that you used to select chassis. The software should > > > communicate with the chipper check. If there is no communication it will > > > tell you. After this go to the top of the program and you can select > reset > > > EPROM. > > > I removed the EPROM from the chassis ,this eliminated the need to > ground > > it > > > when it is in the chassis. > > > > > > I hope this helps, > > > > > > Bruce. > > > B&T Electronics > > > > > > ----- Original Message ----- > > > From: "Bill S" <billans@xxxxxxxxxxxx> > > > To: <techassist@xxxxxxxxxxxxx> > > > Sent: Tuesday, July 23, 2002 3:40 PM > > > Subject: [TechAssist] Questions on hooking up Chipper checker > > > > > > > > > > > > > > Hi all > > > > We got this new chipper checker in and are using it for initializing a > > CTC > > > > 187 and learning about this at the same time. The instructions say to > > > > ground either pin 2 or pin 1 (depending on who made the micro u 3101. > I > > > > found the instructions up to this point but now tried to go to the > next > > > > setup procedure and I got to be honest, I have not found it and am > > > starting > > > > to feel real stupid now. I'm not totally computer illiterate but am > > > > starting to think I should have written the instuctions as it would be > a > > > bit > > > > more easier to follow. Where else am I to look in the instructions? > > > > Thanks > > > > Bill Sorensen > > > > New Life Video & Audio > > > > billans@xxxxxxxxxxxx > > > > - - - - - - - - - - - - - - - - - - - > > > > > > > > > > > > > > > > > > > > ------------------------------------------ > > > > To REMOVE your email address, click here: > > > > http://www.tech-assist.org/unsubb.html > > > > To CHANGE your email address, click here: > > > > http://www.tech-assist.org/change.html > > > > ------------------------------------------ > > > > ***NEW*** Tips Added Instantly!!!*** > > > > Submit Repair Tips here: > > > > http://www.tech-assist.org/secure/tip/ > > > > > > ------------------------------------------ > > > To REMOVE your email address, click here: > > > http://www.tech-assist.org/unsubb.html > > > To CHANGE your email address, click here: > > > http://www.tech-assist.org/change.html > > > ------------------------------------------ > > > ***NEW*** Tips Added Instantly!!!*** > > > Submit Repair Tips here: > > > http://www.tech-assist.org/secure/tip/ > > > > > > > > > > > ------------------------------------------ > > To REMOVE your email address, click here: > > http://www.tech-assist.org/unsubb.html > > To CHANGE your email address, click here: > > http://www.tech-assist.org/change.html > > ------------------------------------------ > > ***NEW*** Tips Added Instantly!!!*** > > Submit Repair Tips here: > > http://www.tech-assist.org/secure/tip/ > > ------------------------------------------ > To REMOVE your email address, click here: > http://www.tech-assist.org/unsubb.html > To CHANGE your email address, click here: > http://www.tech-assist.org/change.html > ------------------------------------------ > ***NEW*** Tips Added Instantly!!!*** > Submit Repair Tips here: > http://www.tech-assist.org/secure/tip/ > ------------------------------------------ To REMOVE your email address, click here: http://www.tech-assist.org/unsubb.html To CHANGE your email address, click here: http://www.tech-assist.org/change.html ------------------------------------------ ***NEW*** Tips Added Instantly!!!*** Submit Repair Tips here: http://www.tech-assist.org/secure/tip/