[TechAssist] Re: More help needed -GE JVM140H Range hood Spacemaker 1400 No heat.
- From: Roger G <rogerfixit@xxxxxxxxxxx>
- To: techassist@xxxxxxxxxxxxx
- Date: Thu, 01 Jul 2004 22:06:12 -0400
Alignment is good - Ck'd continuity using door itself.
Also ck'd high voltage side by putting 110v to transformer.
BTW, did not see any secondary high voltage tap from transformer as mentioned.
Will go over ckt bd with magnifier - sounding more and more like micro [?]
Roger G.
Mr. Fix-It
Harrisburg, PA 17110 WebSite- http://mrfixit.netfirms.com
rogerfixit@xxxxxxxx
FAX 510-740-3641; Tel: 717-763-7098 (shop) 717-652-1703(home)
At 10:18 PM 6/29/2004, you wrote:
>Did you check the alignment of the switches? Check for bad solder on the
>control board.
>Al Marquardt
>ampm@xxxxxxx
>Al Marquardt Electronic Repair
>206 W Main
>Girardville Pa. 17935
>----- Original Message -----
>From: "Roger G" <rogerfixit@xxxxxxxxxxx>
>To: <techassist@xxxxxxxxxxxxx>
>Sent: Tuesday, June 29, 2004 9:39 PM
>Subject: [TechAssist] Re: More help needed -GE JVM140H Range hood Spacemaker
>1400 No heat.
>
>
> > Subbed all micro switches - no better - actually, now acting weirdly.
> >
> > Set time cook - hit Start. Unit starts up but no heat.
> > If I open the door, fan stops, light comes on BUT timer keeps counting
>down !!
> > If I close the door, power starts up without having to hit START - still
>no
> > heat.
> > If the door is open when the time runs out, a relay clicks.
> > If the door is closed, beeper beeps and shows END.
> >
> > All ideas appreciated
> >
> >
> > Did check and looked ok but I have it on a table - he uses it hanging on
> > the wall so it is possible that the door alignment could be off - except -
> > he said he took it home and tried it on the table without hanging it.
> > Maybe something happened in transit.
> > I usually run these and move the door up and down to assure alignment.
> > Roger G.
> >
> > Mr. Fix-It
> > Harrisburg, PA 17110 WebSite- http://mrfixit.netfirms.com
> > rogerfixit@xxxxxxxx
> > FAX 510-740-3641; Tel: 717-763-7098 (shop) 717-652-1703(home)
> >
> > At 11:09 PM 6/18/2004, you wrote:
> >
> > >Even though the switches check good how does the alignment look?
> > >Al Marquardt
> > >ampm@xxxxxxx
> > >Al Marquardt Electronic Repair
> > >206 W Main
> > >Girardville Pa. 17935
> > >----- Original Message -----
> > >From: "Roger G" <rogerfixit@xxxxxxxxxxx>
> > >To: <techassist@xxxxxxxxxxxxx>
> > >Cc: <hivolts@xxxxxxxxxxxxxxxx>; <becyn@xxxxxxxxxx>
> > >Sent: Friday, June 18, 2004 5:05 PM
> > >Subject: [TechAssist] GE JVM140H Range hood Spacemaker 1400 No heat.
> > >
> > >
> > > > REgarding the comments on the Sharp Microwave on TechAssist,
> > > > Just did a GE with VERY intermittent heating. Resoldered the ckt bd as
> > > > suggested.
> > > > It worked every time for me - even before I soldered the bd- and
>always
> > >after.
> > > > Custy took it home - said it does not work.
> > > > I had checked the micro switches-- chk'd OK.
> > > > Have you found a similar problem with these GE microwaves?
> > > > The connectors looked clean - not like the ones where the grease gets
>into
> > > > them and turns them brown
> > > >
> > > > Roger G.
> > > >
> > > > Mr. Fix-It
> > > > Harrisburg, PA 17110 WebSite- http://mrfixit.netfirms.com
> > > > rogerfixit@xxxxxxxx
> > > > FAX 510-740-3641; Tel: 717-763-7098 (shop) 717-652-1703(home)
> > > >
> >
-----------------------------------------------------------------------------
Lost Password:
http://www.tech-assist.org and select "Login Problems?".
Email Archives:
//www.freelists.org/archives/techassist/
Other related posts:
