Bart - Be careful of extreme statements... I would not say that "a bare capacitor ESL value is not of interest," and that "inductance values listed in these models are of no value for the end user." Istvan, Nick and I are saying that you have to be very careful about where the inductance values used in power distribution simulation came from. "Partial" self and mutual inductances are not unique. They have to be interpreted in the context of a loop. You could have several different self and mutual inductances for each element of a loop and they may all be self consistent and correct in the context of a loop. This means that when you go around the loop, you get the correct loop inductance. I don't know how to get an exact inductance to represent the intrinsic inductance of a capacitor. I don't believe that such a thing exists. It is however possible to use a fixture that is very similar to your product environment and obtain a sufficiently accurate inductance for the capacitor. A power distribution system is likely to be very low (less than 1 Ohm) in impedance. Capacitors mounted on such a structure will behave quite differently than capacitors mounted on a 50 Ohm structure. By using a fixture that is similar to your product environment, it is possible to obtain an intrinsic inductance value for a capacitor that is useful for SQPI simulation and will produce good model to hardware correlation results in a complete power distribution system. It is even possible to obtain the parameters for a distributed transmission line model for the capacitor which will obtain even better model to hardware correlation, as discussed in our papers. This however is outside the scope of what SQPI is presently offering. regards, Larry Smith Sun Microsystems > Delivered-To: si-list@xxxxxxxxxxxxx > To: istvan.novak@xxxxxxxxxxxxxxxx > Cc: si-list@xxxxxxxxxxxxx, si-list-bounce@xxxxxxxxxxxxx > Subject: [SI-LIST] Re: resend - Specctraquest model: mounted inductance > MIME-Version: 1.0 > From: "Bart Bouma" <bart.bouma@xxxxxxxxx> > Date: Mon, 16 Jun 2003 12:11:14 +0200 > X-MIMETrack: Serialize by Router on EURM01/SERVER/YAGEO(Release 5.0.5 |September 22, 2000) at 06/16/2003 11:11:20 AM, Serialize complete at 06/16/2003 11:11:20 AM > Content-Transfer-Encoding: 8bit > X-archive-position: 7125 > X-ecartis-version: Ecartis v1.0.0 > X-original-sender: bart.bouma@xxxxxxxxx > X-list: si-list > > Istvan, > thanks for the detailed answer. > After the discussions during the past weeks on this subject (thanks also > go to Larry and Nick), I am aware that just a bare capacitor ESL value is > not of interest and useful for modern designs. > Question: what's the added value of having e.g. a Specctraquest model with > values for intrinsic and mounted inductance then? > That's where it all started about, maybe I'm wrong, but I believe that Sun > was involved in defining these models. Are these models superseded ? > Without knowing the configuration the inductance values listed in these > models are of no value for the end user. Please correct me when I'm wrong. > > The tips you gave for the capacitor manufacturers at the bottom of your > answer will be helpful to give better defined "ESL"-values: we will study > these and see what's possible to realize. > Here some comments and remarks: ------------------------------------------------------------------ To unsubscribe from si-list: si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field or to administer your membership from a web page, go to: //www.freelists.org/webpage/si-list For help: si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field List archives are viewable at: //www.freelists.org/archives/si-list or at our remote archives: http://groups.yahoo.com/group/si-list/messages Old (prior to June 6, 2001) list archives are viewable at: http://www.qsl.net/wb6tpu