[PCB_FORUM] Re: [RMX:#] drill quit working.
- From: sjchar3@xxxxxxxxxxxx
- To: icu-pcb-forum@xxxxxxxxxxxxx
- Date: Wed, 29 Aug 2012 11:57:18 -0400 (EDT)
Blake, We switched servers recently, could the environment variable be the
problem. Do the "CDC_LIC_FILE" and "LM_LICENSE_FILE" have to match?
-----Original Message-----
From: Moore, Blake <Blake.Moore@xxxxxxxxxx>
To: icu-pcb-forum <icu-pcb-forum@xxxxxxxxxxxxx>
Sent: Wed, Aug 29, 2012 8:48 am
Subject: [PCB_FORUM] Re: [RMX:#] drill quit working.
Ok, and you have looked at where it would have put the file?
It’s not always where the working directory is…..
And you are checking the location it might have put it at, not always the
working directory,,, like we assume sometimes
If it was working, it’s not like something would have gotten deleted in your
settings, and nc legend still works
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of sjchar3@xxxxxxxxxxxx
Sent: Wednesday, August 29, 2012 11:35 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: [RMX:#] drill quit working.
Thanks Blake, I'm pressing the right buttons but the NC Drill GUI does not pop
up. I get the NCtape_full at the bottom of screen.
Sam
-----Original Message-----
From: Moore, Blake <Blake.Moore@xxxxxxxxxx>
To: icu-pcb-forum <icu-pcb-forum@xxxxxxxxxxxxx>
Sent: Wed, Aug 29, 2012 8:19 am
Subject: [PCB_FORUM] Re: [RMX:#] drill quit working.
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of sjchar3@xxxxxxxxxxxx
Sent: Wednesday, August 29, 2012 11:02 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: [RMX:#] drill quit working.
Im using allegro 16.3. At the bottom of the GUI I see "nctape_full". I brought
in the NClegend and the vias were updated, but i don't have a "DRL" file.
Thanks for all replies.
-----Original Message-----
From: TEYSSIER Jean-Charles <jcteyssier@xxxxxxxxxxxxxxx>
To: icu-pcb-forum <icu-pcb-forum@xxxxxxxxxxxxx>
Sent: Wed, Aug 29, 2012 6:10 am
Subject: [PCB_FORUM] Re: [RMX:#] drill quit working.
Some cheks :
- no space in directory names.
- Space disk left ?
- No space in temp directory name
Jean-Charles TEYSSIER
De : icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] De la part de Matija Golar
Envoyé : mercredi 29 août 2012 15:03
À : icu-pcb-forum@xxxxxxxxxxxxx
Objet : [PCB_FORUM] Re: [RMX:#] drill quit working.
i think it is more trivial...
try entering ncdrill config and change 1 parameter, so config file gets
rewritten, then start drill again
i remember seeing something like this once...
regards,
Matija
On 29.8.2012 14:55, isco catanyag wrote:
Try to install latest hotfix.
From: TEYSSIER Jean-Charles <jcteyssier@xxxxxxxxxxxxxxx>
To: icu-pcb-forum@xxxxxxxxxxxxx
Sent: Wednesday, August 29, 2012 2:09 PM
Subject: [PCB_FORUM] Re: [RMX:#] drill quit working.
Hi sam,
Which allegro version and which symptoms ?
Jean-Charles TEYSSIER
De : icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] De la part de sjchar3@xxxxxxxxxxxx
Envoyé : mercredi 29 août 2012 01:29
À : icu-pcb-forum@xxxxxxxxxxxxx
Objet : [RMX:#] [PCB_FORUM] drill quit working.
Group:
Not sure what happened but the drill functions isn't working anymore.
Any help would be appreciated.
Thanks sam
Other related posts:
