Thanks Sam,,I deleted the "home" variable and drill is working again.. Thanks to all Sam -----Original Message----- From: Moore, Blake <Blake.Moore@xxxxxxxxxx> To: icu-pcb-forum <icu-pcb-forum@xxxxxxxxxxxxx> Sent: Wed, Aug 29, 2012 9:06 am Subject: [PCB_FORUM] Re: [RMX:#] drill quit working. I don’t know about the servers, etc… but it’s pretty safe to say, switching servers seems to have always had problems to work out, no matter where we are. Would it make sense to copy a nc_param.txt file from a known good board file directory, and put it in your working directory, if that worked, then you would be able to edit the NC paramters if needed, etc.. From: icu-pcb-forum-bounce@xxxxxxxxxxxxx [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of sjchar3@xxxxxxxxxxxx Sent: Wednesday, August 29, 2012 11:57 AM To: icu-pcb-forum@xxxxxxxxxxxxx Subject: [PCB_FORUM] Re: [RMX:#] drill quit working. Blake, We switched servers recently, could the environment variable be the problem. Do the "CDC_LIC_FILE" and "LM_LICENSE_FILE" have to match? -----Original Message----- From: Moore, Blake <Blake.Moore@xxxxxxxxxx> To: icu-pcb-forum <icu-pcb-forum@xxxxxxxxxxxxx> Sent: Wed, Aug 29, 2012 8:48 am Subject: [PCB_FORUM] Re: [RMX:#] drill quit working. Ok, and you have looked at where it would have put the file? It’s not always where the working directory is….. And you are checking the location it might have put it at, not always the working directory,,, like we assume sometimes If it was working, it’s not like something would have gotten deleted in your settings, and nc legend still works From: icu-pcb-forum-bounce@xxxxxxxxxxxxx [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of sjchar3@xxxxxxxxxxxx Sent: Wednesday, August 29, 2012 11:35 AM To: icu-pcb-forum@xxxxxxxxxxxxx Subject: [PCB_FORUM] Re: [RMX:#] drill quit working. Thanks Blake, I'm pressing the right buttons but the NC Drill GUI does not pop up. I get the NCtape_full at the bottom of screen. Sam -----Original Message----- From: Moore, Blake <Blake.Moore@xxxxxxxxxx> To: icu-pcb-forum <icu-pcb-forum@xxxxxxxxxxxxx> Sent: Wed, Aug 29, 2012 8:19 am Subject: [PCB_FORUM] Re: [RMX:#] drill quit working. From: icu-pcb-forum-bounce@xxxxxxxxxxxxx [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of sjchar3@xxxxxxxxxxxx Sent: Wednesday, August 29, 2012 11:02 AM To: icu-pcb-forum@xxxxxxxxxxxxx Subject: [PCB_FORUM] Re: [RMX:#] drill quit working. Im using allegro 16.3. At the bottom of the GUI I see "nctape_full". I brought in the NClegend and the vias were updated, but i don't have a "DRL" file. Thanks for all replies. -----Original Message----- From: TEYSSIER Jean-Charles <jcteyssier@xxxxxxxxxxxxxxx> To: icu-pcb-forum <icu-pcb-forum@xxxxxxxxxxxxx> Sent: Wed, Aug 29, 2012 6:10 am Subject: [PCB_FORUM] Re: [RMX:#] drill quit working. Some cheks : - no space in directory names. - Space disk left ? - No space in temp directory name Jean-Charles TEYSSIER De : icu-pcb-forum-bounce@xxxxxxxxxxxxx [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] De la part de Matija Golar Envoyé : mercredi 29 août 2012 15:03 À : icu-pcb-forum@xxxxxxxxxxxxx Objet : [PCB_FORUM] Re: [RMX:#] drill quit working. i think it is more trivial... try entering ncdrill config and change 1 parameter, so config file gets rewritten, then start drill again i remember seeing something like this once... regards, Matija On 29.8.2012 14:55, isco catanyag wrote: Try to install latest hotfix. From: TEYSSIER Jean-Charles <jcteyssier@xxxxxxxxxxxxxxx> To: icu-pcb-forum@xxxxxxxxxxxxx Sent: Wednesday, August 29, 2012 2:09 PM Subject: [PCB_FORUM] Re: [RMX:#] drill quit working. Hi sam, Which allegro version and which symptoms ? Jean-Charles TEYSSIER De : icu-pcb-forum-bounce@xxxxxxxxxxxxx [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] De la part de sjchar3@xxxxxxxxxxxx Envoyé : mercredi 29 août 2012 01:29 À : icu-pcb-forum@xxxxxxxxxxxxx Objet : [RMX:#] [PCB_FORUM] drill quit working. Group: Not sure what happened but the drill functions isn't working anymore. Any help would be appreciated. Thanks sam