Ok, and you have looked at where it would have put the file? It’s not always where the working directory is….. And you are checking the location it might have put it at, not always the working directory,,, like we assume sometimes If it was working, it’s not like something would have gotten deleted in your settings, and nc legend still works From: icu-pcb-forum-bounce@xxxxxxxxxxxxx [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of sjchar3@xxxxxxxxxxxx Sent: Wednesday, August 29, 2012 11:35 AM To: icu-pcb-forum@xxxxxxxxxxxxx Subject: [PCB_FORUM] Re: [RMX:#] drill quit working. Thanks Blake, I'm pressing the right buttons but the NC Drill GUI does not pop up. I get the NCtape_full at the bottom of screen. Sam -----Original Message----- From: Moore, Blake <Blake.Moore@xxxxxxxxxx<mailto:Blake.Moore@xxxxxxxxxx>> To: icu-pcb-forum <icu-pcb-forum@xxxxxxxxxxxxx<mailto:icu-pcb-forum@xxxxxxxxxxxxx>> Sent: Wed, Aug 29, 2012 8:19 am Subject: [PCB_FORUM] Re: [RMX:#] drill quit working. From: icu-pcb-forum-bounce@xxxxxxxxxxxxx<mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx> [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx<mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx?>] On Behalf Of sjchar3@xxxxxxxxxxxx<mailto:sjchar3@xxxxxxxxxxxx> Sent: Wednesday, August 29, 2012 11:02 AM To: icu-pcb-forum@xxxxxxxxxxxxx<mailto:icu-pcb-forum@xxxxxxxxxxxxx> Subject: [PCB_FORUM] Re: [RMX:#] drill quit working. Im using allegro 16.3. At the bottom of the GUI I see "nctape_full". I brought in the NClegend and the vias were updated, but i don't have a "DRL" file. Thanks for all replies. -----Original Message----- From: TEYSSIER Jean-Charles <jcteyssier@xxxxxxxxxxxxxxx<mailto:jcteyssier@xxxxxxxxxxxxxxx>> To: icu-pcb-forum <icu-pcb-forum@xxxxxxxxxxxxx<mailto:icu-pcb-forum@xxxxxxxxxxxxx>> Sent: Wed, Aug 29, 2012 6:10 am Subject: [PCB_FORUM] Re: [RMX:#] drill quit working. Some cheks : - no space in directory names. - Space disk left ? - No space in temp directory name Jean-Charles TEYSSIER ________________________________ De : icu-pcb-forum-bounce@xxxxxxxxxxxxx<mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx> [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx<mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx?>] De la part de Matija Golar Envoyé : mercredi 29 août 2012 15:03 À : icu-pcb-forum@xxxxxxxxxxxxx<mailto:icu-pcb-forum@xxxxxxxxxxxxx> Objet : [PCB_FORUM] Re: [RMX:#] drill quit working. i think it is more trivial... try entering ncdrill config and change 1 parameter, so config file gets rewritten, then start drill again i remember seeing something like this once... regards, Matija On 29.8.2012 14:55, isco catanyag wrote: Try to install latest hotfix. ________________________________ From: TEYSSIER Jean-Charles <jcteyssier@xxxxxxxxxxxxxxx><mailto:jcteyssier@xxxxxxxxxxxxxxx> To: icu-pcb-forum@xxxxxxxxxxxxx<mailto:icu-pcb-forum@xxxxxxxxxxxxx> Sent: Wednesday, August 29, 2012 2:09 PM Subject: [PCB_FORUM] Re: [RMX:#] drill quit working. Hi sam, Which allegro version and which symptoms ? Jean-Charles TEYSSIER ________________________________ De : icu-pcb-forum-bounce@xxxxxxxxxxxxx<mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx> [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] De la part de sjchar3@xxxxxxxxxxxx<mailto:sjchar3@xxxxxxxxxxxx> Envoyé : mercredi 29 août 2012 01:29 À : icu-pcb-forum@xxxxxxxxxxxxx<mailto:icu-pcb-forum@xxxxxxxxxxxxx> Objet : [RMX:#] [PCB_FORUM] drill quit working. Group: Not sure what happened but the drill functions isn't working anymore. Any help would be appreciated. Thanks sam