[PCB_FORUM] Re: Help!!! Segment with same start and end points
- From: "Van Huynh (huynh)" <huynh@xxxxxxxxx>
- To: <icu-pcb-forum@xxxxxxxxxxxxx>
- Date: Sat, 18 Dec 2004 10:38:35 -0800
My dangling report is clean.
It's seem like I have some elements out of dwg extend and I can not get to
it.
Van Huynh
_____
From: Selvakumar [mailto:selva@xxxxxxxxxxxxx]
Sent: Saturday, December 18, 2004 10:29 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Help!!! Segment with same start and end points
Please run these allego scripts.This will show the danglings.validate the
dangling and delete.
regards
Selva
-----Original Message-----
From: Gerry Meier [mailto:gerry.meier@xxxxxxxxxxxxxx]
Sent: Saturday, December 18, 2004 11:23 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Help!!! Segment with same start and end points
Van,
When you run your summary report or dangling line report are there dangling
lines?
If so "in a copy database" try glossing the dangling lines have "only" line
smoothing checked and "only" dangling lines inside line smoothing form
checked.
Gerry
Gerry Meier
Sr. PCB Designer
Freedom CAD Services, Inc.
Voice: (603) 864-1300 x1350
Alt. Voice: (386) 753-0048
Email: gerry.meier@xxxxxxxxxxxxxx
visit our website at<http://www.freedomcad.com <http://www.freedomcad.com/>
_____
From: Van Huynh (huynh) [mailto:huynh@xxxxxxxxx]
Sent: Saturday, December 18, 2004 12:46 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Help!!! Segment with same start and end points
I ran DBDoctor within the database and outside on the shell command line
still doesn't help.
Thanks for input
Van Huynh
_____
From: Gerry Meier [mailto:gerry.meier@xxxxxxxxxxxxxx]
Sent: Saturday, December 18, 2004 9:41 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Help!!! Segment with same start and end points
try running dbdoctor on the database
Gerry Meier
Sr. PCB Designer
Freedom CAD Services, Inc.
Voice: (603) 864-1300 x1350
Alt. Voice: (386) 753-0048
Email: gerry.meier@xxxxxxxxxxxxxx
visit our website at<http://www.freedomcad.com <http://www.freedomcad.com/>
_____
From: Van Huynh (huynh) [mailto:huynh@xxxxxxxxx]
Sent: Saturday, December 18, 2004 12:37 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Help!!! Segment with same start and end points
I got a lots of these warning on every artwork layers,
Any one know how to fix these errors message?
WARNING: Segment with same start and end points at
(75.2869 -194448.6314) will be ignored. Increasing output
accuracy may allow segment to be generated.
My artwork parameter setup:
DEVICE-TYPE GERBER_RS274X
OUTPUT-UNITS INCHES
FILM-SIZE 240000 160000
FORMAT 2.5
ABORT-ON-ERROR NO
SCALE 1
SUPPRESS-LEAD-ZEROES YES
SUPPRESS-TRAIL-ZEROES NO
SUPPRESS-EQUAL YES
UNDEF-APT-CONT NO
NC Drill format is 2.5
Drawing parameter accuracy is 4
Thank you
Van Huynh
Other related posts:
