[ddots-l] Re: suddenly getting error about display setting
- From: Efren Chavez <efrenchavez91@xxxxxxxxx>
- To: ddots-l@xxxxxxxxxxxxx
- Date: Wed, 4 Feb 2015 19:38:31 -0500
Hey Dave,
Go to the adjust screen resolution and make sure its not on portrait.
Set it to Landscape and the correct order of numbers should appear.
On 2/4/15, Dave Hillebrandt <dave@xxxxxxxx> wrote:
> Thanks for suggestion. This is actually in windows xp, and able to read the
> actual numbers but the one wanted is not listed. You mention presentation
> mode and dont know anything about this. I even have a selection of 768
> by1024 but not the other way around for 1024 by 768.
> ----- Original Message -----
> From: D!J!X!
> To: ddots-l@xxxxxxxxxxxxx
> Sent: Wednesday, February 04, 2015 6:18 PM
> Subject: [ddots-l] Re: suddenly getting error about display setting
>
>
> Are you using Windows 7? If so it probably reads it as percentages,
> specially if you have an intel built-in graphics such as the 3000, 4000 or
> 4600.
>
> If so, set a percentage and press tab, then jaws will read the actual
> numbers. Then you can shift tab to find the bar and move it up and down.
>
>
>
> HTH, D!J!X!
>
>
>
> From: ddots-l-bounce@xxxxxxxxxxxxx [mailto:ddots-l-bounce@xxxxxxxxxxxxx]
> On Behalf Of Dave Hillebrandt
> Sent: Wednesday, February 04, 2015 5:51 PM
> To: ddots-l@xxxxxxxxxxxxx
> Subject: [ddots-l] Re: suddenly getting error about display setting
>
>
>
> Thanks, will definitely get some sighted assistance to confirm what I'm
> seeing with jaws. very true about it not always being screen reader
> friendly, however is reading these selections, and quite strangely, this
> 1024 by 768 is not a choice given so is where I am not and got to find a
> tech who knows how to make this come up.
>
> ----- Original Message -----
>
> From: Bill
>
> To: ddots-l@xxxxxxxxxxxxx
>
> Sent: Wednesday, February 04, 2015 5:43 PM
>
> Subject: [ddots-l] Re: suddenly getting error about display setting
>
>
>
> Yes, 1024 by 768 is what you want. Unless somebody swapped your video
> card out for another, there's no doubt that your card can be set to that
> resolution. But that Windows is not at all screen-reader friendly. You may
> need to tab to the field that shows resolutions and then press right or left
> arrow. Then, to read the new value, you must tab away from the field and
> then tab back. Probably fastest to recruit a sighted assistant.
>
>
>
> From: ddots-l-bounce@xxxxxxxxxxxxx [mailto:ddots-l-bounce@xxxxxxxxxxxxx]
> On Behalf Of Dave Hillebrandt
> Sent: Wednesday, February 04, 2015 5:32 PM
> To: ddots-l@xxxxxxxxxxxxx
> Subject: [ddots-l] Re: suddenly getting error about display setting
>
>
>
> No, I'm afraid not, though could see how it might do that. No, hadn't
> been connected to anything unusual and a bit baffling. Wondering if it could
> be a virus or something.
>
> If you know, could you varify that the display needs to be either 1024,
> 1152 or 1280 for horizontal and 768 for vertical? Since this is not one of
> the choices, am wondering if there is a way of getting in somewhere in
> between what is offered if you know what I mean.
>
> I see a couple with horizontal settings of 1024 and or 1152 but none of
> them have a vertical setting of 768.... Thanks in advance
>
> ----- Original Message -----
>
> From: Bill
>
> To: ddots-l@xxxxxxxxxxxxx
>
> Sent: Wednesday, February 04, 2015 5:22 PM
>
> Subject: [ddots-l] Re: suddenly getting error about display setting
>
>
>
> Dave, is it possible that you or anyone else connected your machine to
> a video projector or auxiliary video display? If so, it is likely that good
> old Windows changed your display settings for you without even asking.
>
>
>
> From: ddots-l-bounce@xxxxxxxxxxxxx
> [mailto:ddots-l-bounce@xxxxxxxxxxxxx] On Behalf Of Dave Hillebrandt
> Sent: Wednesday, February 04, 2015 10:54 AM
> To: ddots-l@xxxxxxxxxxxxx
> Subject: [ddots-l] suddenly getting error about display setting
>
>
>
> Hello Friends, Just went into Sonar 8.3 and getting message that my
> display is set to the wrong resolution. Haven't changed anything in display
> for a couple years so dont know how it could change. Then, when I go into
> display to change setting, I cang find one that is both horiz 1024, 1152, or
> 1280 alongwith vertical of 768 as nessage states, did i understand this
> message correctly, and if so, how would display settings change like that on
> their own? Are there possibly other values that I'm not seeing as seems to
> have many choices but not one I need. Using Windows XP. Thanks for any
> ideas. Dave
>
--
Efren Chavez
PLEASE READ THIS FOOTER AT LEAST ONCE!
To leave the list, click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe
If this link doesn't work then send a message to:
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
unsubscribe
For other list commands such as vacation mode,
click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subject=faq or
send a message, to
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
faq
Other related posts:
