For future reference, go to the intel tray icon and disable hotkeys... -----Original Message----- From: ddots-l-bounce@xxxxxxxxxxxxx [mailto:ddots-l-bounce@xxxxxxxxxxxxx] On Behalf Of Dave Hillebrandt Sent: Wednesday, February 04, 2015 11:17 PM To: ddots-l@xxxxxxxxxxxxx Subject: [ddots-l] Re: suddenly getting error about display setting Found it. Thanks much. Googled how to change from portrate to landscape. control alt up-arrow. obviously when speech was off it happened, because that short cut doesn't work while jaws is on. quite relieved. Dave ----- Original Message ----- From: "Efren Chavez" <efrenchavez91@xxxxxxxxx> To: <ddots-l@xxxxxxxxxxxxx> Sent: Wednesday, February 04, 2015 7:38 PM Subject: [ddots-l] Re: suddenly getting error about display setting > Hey Dave, > Go to the adjust screen resolution and make sure its not on portrait. > Set it to Landscape and the correct order of numbers should appear. > > > On 2/4/15, Dave Hillebrandt <dave@xxxxxxxx> wrote: >> Thanks for suggestion. This is actually in windows xp, and able to >> read the actual numbers but the one wanted is not listed. You mention >> presentation mode and dont know anything about this. I even have a >> selection of 768 >> by1024 but not the other way around for 1024 by 768. >> ----- Original Message ----- >> From: D!J!X! >> To: ddots-l@xxxxxxxxxxxxx >> Sent: Wednesday, February 04, 2015 6:18 PM >> Subject: [ddots-l] Re: suddenly getting error about display setting >> >> >> Are you using Windows 7? If so it probably reads it as percentages, >> specially if you have an intel built-in graphics such as the 3000, >> 4000 or 4600. >> >> If so, set a percentage and press tab, then jaws will read the >> actual numbers. Then you can shift tab to find the bar and move it up and down. >> >> >> >> HTH, D!J!X! >> >> >> >> From: ddots-l-bounce@xxxxxxxxxxxxx >> [mailto:ddots-l-bounce@xxxxxxxxxxxxx] >> On Behalf Of Dave Hillebrandt >> Sent: Wednesday, February 04, 2015 5:51 PM >> To: ddots-l@xxxxxxxxxxxxx >> Subject: [ddots-l] Re: suddenly getting error about display setting >> >> >> >> Thanks, will definitely get some sighted assistance to confirm what >> I'm seeing with jaws. very true about it not always being screen >> reader friendly, however is reading these selections, and quite >> strangely, this >> 1024 by 768 is not a choice given so is where I am not and got to >> find a tech who knows how to make this come up. >> >> ----- Original Message ----- >> >> From: Bill >> >> To: ddots-l@xxxxxxxxxxxxx >> >> Sent: Wednesday, February 04, 2015 5:43 PM >> >> Subject: [ddots-l] Re: suddenly getting error about display >> setting >> >> >> >> Yes, 1024 by 768 is what you want. Unless somebody swapped your >> video card out for another, there's no doubt that your card can be >> set to that resolution. But that Windows is not at all screen-reader >> friendly. You may need to tab to the field that shows resolutions >> and then press right or left arrow. Then, to read the new value, you >> must tab away from the field and then tab back. Probably fastest to >> recruit a sighted assistant. >> >> >> >> From: ddots-l-bounce@xxxxxxxxxxxxx >> [mailto:ddots-l-bounce@xxxxxxxxxxxxx] >> On Behalf Of Dave Hillebrandt >> Sent: Wednesday, February 04, 2015 5:32 PM >> To: ddots-l@xxxxxxxxxxxxx >> Subject: [ddots-l] Re: suddenly getting error about display setting >> >> >> >> No, I'm afraid not, though could see how it might do that. No, hadn't >> been connected to anything unusual and a bit baffling. Wondering if it >> could >> be a virus or something. >> >> If you know, could you varify that the display needs to be either >> 1024, >> 1152 or 1280 for horizontal and 768 for vertical? Since this is not one >> of >> the choices, am wondering if there is a way of getting in somewhere in >> between what is offered if you know what I mean. >> >> I see a couple with horizontal settings of 1024 and or 1152 but none >> of >> them have a vertical setting of 768.... Thanks in advance >> >> ----- Original Message ----- >> >> From: Bill >> >> To: ddots-l@xxxxxxxxxxxxx >> >> Sent: Wednesday, February 04, 2015 5:22 PM >> >> Subject: [ddots-l] Re: suddenly getting error about display setting >> >> >> >> Dave, is it possible that you or anyone else connected your machine >> to >> a video projector or auxiliary video display? If so, it is likely that >> good >> old Windows changed your display settings for you without even asking. >> >> >> >> From: ddots-l-bounce@xxxxxxxxxxxxx >> [mailto:ddots-l-bounce@xxxxxxxxxxxxx] On Behalf Of Dave Hillebrandt >> Sent: Wednesday, February 04, 2015 10:54 AM >> To: ddots-l@xxxxxxxxxxxxx >> Subject: [ddots-l] suddenly getting error about display setting >> >> >> >> Hello Friends, Just went into Sonar 8.3 and getting message that my >> display is set to the wrong resolution. Haven't changed anything in >> display >> for a couple years so dont know how it could change. Then, when I go into >> display to change setting, I cang find one that is both horiz 1024, 1152, >> or >> 1280 alongwith vertical of 768 as nessage states, did i understand this >> message correctly, and if so, how would display settings change like that >> on >> their own? Are there possibly other values that I'm not seeing as seems >> to >> have many choices but not one I need. Using Windows XP. Thanks for any >> ideas. Dave >> > > > -- > Efren Chavez > PLEASE READ THIS FOOTER AT LEAST ONCE! > To leave the list, click on the immediately following link: > ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe > If this link doesn't work then send a message to: > ddots-l-request@xxxxxxxxxxxxx > and in the Subject line type > unsubscribe > For other list commands such as vacation mode, > click on the immediately following link: > ddots-l-request@xxxxxxxxxxxxx?subject=faq or > send a message, to > ddots-l-request@xxxxxxxxxxxxx > and in the Subject line type > faq > PLEASE READ THIS FOOTER AT LEAST ONCE! To leave the list, click on the immediately following link: ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe If this link doesn't work then send a message to: ddots-l-request@xxxxxxxxxxxxx and in the Subject line type unsubscribe For other list commands such as vacation mode, click on the immediately following link: ddots-l-request@xxxxxxxxxxxxx?subject=faq or send a message, to ddots-l-request@xxxxxxxxxxxxx and in the Subject line type faq PLEASE READ THIS FOOTER AT LEAST ONCE! To leave the list, click on the immediately following link: ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe If this link doesn't work then send a message to: ddots-l-request@xxxxxxxxxxxxx and in the Subject line type unsubscribe For other list commands such as vacation mode, click on the immediately following link: ddots-l-request@xxxxxxxxxxxxx?subject=faq or send a message, to ddots-l-request@xxxxxxxxxxxxx and in the Subject line type faq