Hi Rui, I don't know, but why not give it a go? BTW, I'll be on to your set today/tomorrow mate...I'll be in touch, cheers Steve. Visit: www.vipaudioaccess.com for audio access solutions, articles, demos, to showcase your music and to basically get involved! -----Original Message----- From: ddots-l-bounce@xxxxxxxxxxxxx [mailto:ddots-l-bounce@xxxxxxxxxxxxx] On Behalf Of Rui Vilarinho Sent: 18 November 2013 01:18 To: ddots-l@xxxxxxxxxxxxx Subject: [ddots-l] Re: M-audio Delta 1010LT Sampling Rate Won't Change! Hi Steve and Chris, do you think that this Set also works with the MAudio Profire 2626 soundcard pannel? I mean, does the MAudio control pannel interface is the same for all devices? Thanks, Rui Vilarinho ----- Original Message ----- From: "Steve Spamer" <steve@xxxxxxxxxxxxxxxxxx> To: <ddots-l@xxxxxxxxxxxxx> Sent: Sunday, November 17, 2013 10:30 PM Subject: [ddots-l] Re: M-audio Delta 1010LT Sampling Rate Won't Change! > Chris, if you use HSC, you can download my simple HSC set below. It just > allows you to change sample rate and buffer size. > https://dl.dropboxusercontent.com/u/14684704/M-AudioDeltaControlPanel.hsc > Keystrokes: > Control+Alt+H for the Hardware tab > Control+alt+Equals to increase sample rate > Control+Alt+dash to decrease sample rate > Control+Equals to increase buffer size > Control+Dash to decrease buffer size > > HTH, cheers Steve. > > Visit: > www.vipaudioaccess.com > for audio access solutions, articles, demos, to showcase your music and > to > basically get involved! > -----Original Message----- > From: ddots-l-bounce@xxxxxxxxxxxxx [mailto:ddots-l-bounce@xxxxxxxxxxxxx] > On > Behalf Of Chris Smart > Sent: 17 November 2013 19:24 > To: midimag@xxxxxxxxxxx > Cc: ddots-l@xxxxxxxxxxxxx; audio-discuss@xxxxxxxxxxxxxxx > Subject: [ddots-l] M-audio Delta 1010LT Sampling Rate Won't Change! > > Hi folks. > > I can't get the sampling frequency to change on my Delta 1010LT for some > reason. > > Inside the M-audio Control Pannel, on the hardware tab, I see the word > locked, and 44,100, but can't seem to do a simulated mouse click anywhere > near them that accomplishes anything. > > In Sonar's Audio Options, I try to change the default sampling rate from > 44.1 to 96 KHz, but get an error that the sampling rate cannot be changed, > and has been set to 44.1KHz 32-bit "as suggested by the driver". > > So, do any of you have some precise instructions to share, when it comes > to > using the M-audio Control Pannel? > > If I can figure out where to click, I can at least label graphics for > future > use. > > thanks > > Chris > > PLEASE READ THIS FOOTER AT LEAST ONCE! > To leave the list, click on the immediately following link: > ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe > If this link doesn't work then send a message to: > ddots-l-request@xxxxxxxxxxxxx > and in the Subject line type > unsubscribe > For other list commands such as vacation mode, click on the immediately > following link: > ddots-l-request@xxxxxxxxxxxxx?subject=faq or send a message, to > ddots-l-request@xxxxxxxxxxxxx and in the Subject line type faq > > PLEASE READ THIS FOOTER AT LEAST ONCE! > To leave the list, click on the immediately following link: > ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe > If this link doesn't work then send a message to: > ddots-l-request@xxxxxxxxxxxxx > and in the Subject line type > unsubscribe > For other list commands such as vacation mode, > click on the immediately following link: > ddots-l-request@xxxxxxxxxxxxx?subject=faq or > send a message, to > ddots-l-request@xxxxxxxxxxxxx > and in the Subject line type > faq > > PLEASE READ THIS FOOTER AT LEAST ONCE! To leave the list, click on the immediately following link: ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe If this link doesn't work then send a message to: ddots-l-request@xxxxxxxxxxxxx and in the Subject line type unsubscribe For other list commands such as vacation mode, click on the immediately following link: ddots-l-request@xxxxxxxxxxxxx?subject=faq or send a message, to ddots-l-request@xxxxxxxxxxxxx and in the Subject line type faq PLEASE READ THIS FOOTER AT LEAST ONCE! To leave the list, click on the immediately following link: ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe If this link doesn't work then send a message to: ddots-l-request@xxxxxxxxxxxxx and in the Subject line type unsubscribe For other list commands such as vacation mode, click on the immediately following link: ddots-l-request@xxxxxxxxxxxxx?subject=faq or send a message, to ddots-l-request@xxxxxxxxxxxxx and in the Subject line type faq