[TechAssist] Re: Zenith Projo Z52Z95D8 Picture has Flashing Spells, OSD doesn't display while flashing.
- From: "al m" <ampm@xxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Fri, 18 Oct 2002 09:54:18 -0400
Can you tell us what module the board was on
al jacquard
ampm@xxxxxxx
----- Original Message -----
From: "Lyles Tv" <tech@xxxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Friday, October 18, 2002 9:48 AM
Subject: [TechAssist] Re: Zenith Projo Z52Z95D8 Picture has Flashing Spells,
OSD doesn't display while flashing.
>
> It might be the same or similar problem that I just had on a multiple
> repeat. Someone here helped me---thank you. Check the deflection panel.
> It is standing vertically behind the flyback. My symptom was the picture
> was going dark, but I could see it causing many other intermittant
symptoms.
> I took the board off of the smps module, and was glad I did cause it
allowed
> me to see bad connections I would have otherwise missed if I had left it
on
> the module. It had bad connections ALL over it. BTW. Even after
getting
> the cure to my symptom from someone here, heating, cooling, flexing, and
> tapping would not force it to act up. I allmost blew it off, till I seen
a
> single suspicious joint from the front of set with a flashlight. I will
> ALLWAYS pull and solder these now.
> Jeff Farnsworth
> Lyles TV and Appliance
> 17 S Washington St
> Elkhorn, Wi. 53121
> ph 262-723-3477
> fax 262-723-3658
> tech@xxxxxxxxxxx
> ----- Original Message -----
> From: "Jon Garver" <jongar@xxxxxxxxxxxxx>
> To: "TechAssist" <techassist@xxxxxxxxxxxxx>
> Sent: Thursday, October 17, 2002 5:04 PM
> Subject: [TechAssist] Zenith Projo Z52Z95D8 Picture has Flashing Spells,
OSD
> doesn't display while flashing.
>
>
> >
> > This Zenith projection Z52Z95D8 is a call back. Original problem
> > was dead. Replaced fly, H.O.T., B+ diode. Took it home last week.
> >
> > According to the customer, it is now flickering or flashing. At times
just
> > occasionally, now it is doing it more often, sometimes so bad that you
> > can't see the picture. When it is acting up, they can't access the OSD.
> >
> > Going to look at it next week so I thought maybe someone has seen this
> > before and can give me a clue as to what might be the problem.
> >
> > Thanks,
> >
> > Jon Garver
> > Heritage Television Service
> > Monticello, Indiana
> > 574-583-9681
> > jongar@xxxxxxxxxxxxx or
> > HeritageTV@xxxxxxxxxxx
> >
> >
> >
> > ------------------------------------------
> > To REMOVE your email address, click here:
> > http://www.tech-assist.org/unsubb.html
> > To CHANGE your email address, click here:
> > http://www.techassist.net/forms/change.html
> > ------------------------------------------
> > ***NEW*** Tips Added Instantly!!!***
> > Submit Repair Tips here:
> > http://www.tech-assist.org/secure/tip/
> >
>
> ------------------------------------------
> To REMOVE your email address, click here:
> http://www.tech-assist.org/unsubb.html
> To CHANGE your email address, click here:
> http://www.techassist.net/forms/change.html
> ------------------------------------------
> ***NEW*** Tips Added Instantly!!!***
> Submit Repair Tips here:
> http://www.tech-assist.org/secure/tip/
>
------------------------------------------
To REMOVE your email address, click here:
http://www.tech-assist.org/unsubb.html
To CHANGE your email address, click here:
http://www.techassist.net/forms/change.html
------------------------------------------
***NEW*** Tips Added Instantly!!!***
Submit Repair Tips here:
http://www.tech-assist.org/secure/tip/
Other related posts:
