[TechAssist] FIX complete,RCA P46811LV, PTK195AA convergence power supply+ HV Block input lead

  • From: Phil Bader <tjanphyl@xxxxxxxxxxxxxxx>
  • To: techassist@xxxxxxxxxxxxx
  • Date: Mon, 25 Jul 2005 15:45:41 -0400

OK:
Originally cust. said power failed three times then pic 
bowed,distorted,arcing thru pix.
I replaced the main filter cap 680uf@200V, didn't help.
1) The arc all thru the picture was the HV input lead going into the HV 
block not seated properly.I may change the block if I can't seat it good.
2)Now, picture severly bowed,out of convergence,can not adjust. The 
convergence power supply board uses an STK730-130 with no output.
Changed the STK IC, the PC817 opto-iso(RCA#223653), and the open 
resistor R19717 next to the STK. 30K ohm 2 watt.
Now unit powers on with clear and linear picture with good convergence.
Thanks to this group.
Phil Bader

Philip Bader
Jan Phyl TV Inc. (estab. 1976)
3420 Recker Hwy. Winter Haven, Fl. 33880
Fax (863) 299-8821
email: tjanphyl@xxxxxxxxxxxxxxx
personal/ alt. email: pbader@xxxxxxxxxxxxxxx
see our ad at:
http://jan-phyl-television-pc-monitor-service.9601288257006.worldpages-ads.com/



Phil Bader wrote:

>I still have the bowed picture and no output from the converg. power 
>supply board.I ordered another STK730-130. Before I install it, I found 
>an open 1 watt resistor on the same board: R19717. Bands LOOK like 
>brn-blk-brn , but can't be sure.  need value.
>Phil Bader
>
>Philip Bader
>Jan Phyl TV Inc. (estab. 1976)
>3420 Recker Hwy. Winter Haven, Fl. 33880
>Fax (863) 299-8821
>email: tjanphyl@xxxxxxxxxxxxxxx
>personal/ alt. email: pbader@xxxxxxxxxxxxxxx
>see our ad at:
>http://jan-phyl-television-pc-monitor-service.9601288257006.worldpages-ads.com/
>
>
>
>Phil Bader wrote:
>
>  
>
>>A quick check of the converg. power supply board showed only a few volts 
>>output, so I ordered another STK730 IC for that module.BTW If I unplug 
>>that AC wire/plug from the main board that plugs into the conv. power 
>>supply (delivers the 120VAC) the geometry is unchanged, so with or 
>>without the conv.PS even powered,same look? I think the STK is it. Will 
>>install and see.This is a likely suspect since it started with power 
>>outtages. You are right, it could be a corrupt eeprom. If so, I can 
>>basically just go into the service menu and do a converg. alignment back 
>>where it belongs without replacing the eeprom? When we say "corrupted 
>>eeprom" it really means some of the values changed,thereby affecting 
>>that parameter,I ASS-U-ME!
>>;-)
>>Thanks for the help.
>>Phil
>>
>>Philip Bader
>>Jan Phyl TV Inc. (estab. 1976)
>>3420 Recker Hwy. Winter Haven, Fl. 33880
>>Fax (863) 299-8821
>>email: tjanphyl@xxxxxxxxxxxxxxx
>>personal/ alt. email: pbader@xxxxxxxxxxxxxxx
>>see our ad at:
>>http://jan-phyl-television-pc-monitor-service.9601288257006.worldpages-ads.com/
>>
>>
>>
>>Damon wrote:
>>
>> 
>>
>>    
>>
>>>Did you check the Convergence Power supply to see if it was running? Can you
>>>adjust anything in the Convergence circuit? BTW I think the Convergence
>>>board BOWS only the top and bottom of the picture when the power supply
>>>shuts off.......I think I've had a couple of these units intermittantly turn
>>>itself off, and the price of the board was cheaper than spending hours
>>>identifying the intermittant.
>>>
>>>I think I'd check for adjustability and EEprom storage capability
>>>first....pick a grid point, adjust it out of specs a little, store it, then
>>>back out (use only one out of 3 colors, keep a reference color). Go back in
>>>and see if it "remembers", if so, then the EEprom most likely just lost it's
>>>DATA.
>>>.....and you don't have to invest in a new Conv Board. But if it needs one,
>>>you will RUE the day all manufacturers started putting the sensors on the
>>>edges of their screens. Getting "green-OK" is a pain.
>>>
>>>Damon B
>>>Telrad Electronics
>>>Fort Wayne IN
>>>----- Original Message ----- 
>>>From: "Phil Bader" <tjanphyl@xxxxxxxxxxxxxxx>
>>>To: <techassist@xxxxxxxxxxxxx>
>>>Sent: Thursday, July 21, 2005 3:25 PM
>>>Subject: [TechAssist] partial fix,RCA P46811LV, PTK195AA bowed, jagged
>>>buzzing pix after home power flickered
>>>
>>>
>>>
>>>
>>>   
>>>
>>>      
>>>
>>>>Partial fix. The jagged picture looked like arc, so I reseated the HV
>>>>input lead to the HV Splitter block.Then it cleared up.That was it. Now
>>>>the bowed display. Since the bow happened after multiple power
>>>>outtages,think the eeprom got corrupted?
>>>>Phil
>>>>
>>>>Philip Bader
>>>>Jan Phyl TV Inc. (estab. 1976)
>>>>3420 Recker Hwy. Winter Haven, Fl. 33880
>>>>Fax (863) 299-8821
>>>>email: tjanphyl@xxxxxxxxxxxxxxx
>>>>personal/ alt. email: pbader@xxxxxxxxxxxxxxx
>>>>see our ad at:
>>>>
>>>>  
>>>>
>>>>     
>>>>
>>>>        
>>>>
>>>http://jan-phyl-television-pc-monitor-service.9601288257006.worldpages-ads.com/
>>>
>>>
>>>   
>>>
>>>      
>>>
>>>>Phil Bader wrote:
>>>>
>>>>  
>>>>
>>>>     
>>>>
>>>>        
>>>>
>>>>>Customer said the house power failed 4 times. After that the set looked
>>>>>this way. I can make out the OSD and tuner video and sound, but the
>>>>>picture js very bowed, distorted with a kind of "christmas tree
>>>>>jaggedness. I was thinking the main power supply was faulty. I unplugged
>>>>>the main AC wires to the converg. power supply board but same. ALSO!:
>>>>>The screen G2 wire let go from inside the fly.Looks like a small peice
>>>>>is still in there. Am I screwed there?
>>>>>Phil
>>>>>
>>>>>
>>>>>
>>>>>    
>>>>>
>>>>>       
>>>>>
>>>>>          
>>>>>
>>>>--------------------------------------------------------------------------
>>>>  
>>>>
>>>>     
>>>>
>>>>        
>>>>
>>>---
>>>
>>>
>>>   
>>>
>>>      
>>>
>>>>This Email List is Public. Remove: http://www.tech-assist.org/remove.htm
>>>>Set Vacation
>>>>  
>>>>
>>>>     
>>>>
>>>>        
>>>>
>>>mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation
>>>
>>>
>>>   
>>>
>>>      
>>>
>>>>Lost Password: http://www.tech-assist.org  and select "Login Problems?".
>>>>Email Archives: //www.freelists.org/archives/techassist/
>>>>
>>>>  
>>>>
>>>>     
>>>>
>>>>        
>>>>
>>>-----------------------------------------------------------------------------
>>>This Email List is Public. Remove: http://www.tech-assist.org/remove.htm
>>>Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation
>>>Lost Password: http://www.tech-assist.org  and select "Login Problems?".
>>>Email Archives: //www.freelists.org/archives/techassist/
>>>
>>>
>>>
>>>
>>>   
>>>
>>>      
>>>
>>-----------------------------------------------------------------------------
>>This Email List is Public. Remove: http://www.tech-assist.org/remove.htm
>>Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation
>>Lost Password: http://www.tech-assist.org  and select "Login Problems?".
>>Email Archives: //www.freelists.org/archives/techassist/
>>
>>
>> 
>>
>>    
>>
>-----------------------------------------------------------------------------
>This Email List is Public. Remove: http://www.tech-assist.org/remove.htm
>Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation
>Lost Password: http://www.tech-assist.org  and select "Login Problems?".
>Email Archives: //www.freelists.org/archives/techassist/
>
>
>  
>
-----------------------------------------------------------------------------
This Email List is Public. Remove: http://www.tech-assist.org/remove.htm
Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation
Lost Password: http://www.tech-assist.org  and select "Login Problems?".
Email Archives: //www.freelists.org/archives/techassist/

Other related posts:

  1. Home
  2. techassist
  3. Archive
  4. 07-2005