Did you try disconnecting the splitter from the flyback??? Or changing CR4118?? Al Marquardt ampm@xxxxxxx Al Marquardt Electronic Repair 206 W Main Girardville Pa. 17935 ----- Original Message ----- From: "S. Pasher" <spasher@xxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Sunday, October 10, 2004 3:29 PM Subject: [TechAssist] Re: CTC169PTV > > Thanks for your reply Hollis: I tried what you suggested. After I changed > and checked the caps in SMPS I had 140 V at collector. The set would not > come on and did the same as before. The voltage went low and came back > after > a sec. or so. When I put the light on it the light barely glowed with a > 1sec > on off time interval period and measured 12v max on my digital meter. I > guess I have some more problems in the power supply. Don't have the > switcher > or the controller in stock so will have to send for them. > By the way I tried to send this to you a your email address > (HSWAD@xxxxxxx) > but it come back address unknown. > > Buck Pasher > Buck's TV > Gander Newfoundland > Canada > 709-256-7738 (Fax & Phone) > > > > ----- Original Message ----- > From: <HSWAD@xxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Saturday, October 09, 2004 11:10 AM > Subject: [TechAssist] Re: CTC169PTV > > >> >> A very simple test will give you the value of the regulated B+. Connect a > 60 >> watt light bulb from the collector connection and the emitter connection. > Of >> course remove the HOT transistor from the circuit first. Hollis Bates, > Field >> engineer-retired, Lewiston, Maine, _HSWAD@xxxxxxxx (mailto:HSWAD@xxxxxxx) >> >> In a message dated 10/9/04 8:08:30 AM Eastern >> Daylight Time, ampm@xxxxxxx writes: >> If you Changed the caps in the regulator then disconnect the lead from > the >> flyback to the splitter and see if it turns on. >> Al Marquardt >> ampm@xxxxxxx >> Al Marquardt Electronic Repair >> 206 W Main >> Girardville Pa. 17935 >> ----- Original Message ----- >> From: "S. Pasher" <spasher@xxxxxxxxxxxxx> >> To: <techassist@xxxxxxxxxxxxx> >> Sent: Friday, October 08, 2004 5:25 PM >> Subject: [TechAssist] CTC169PTV >> >> >> > Got the SMPS going but its 157 volts on col of H/O without turn on. > When I >> > press ON it goes down but set turns off and it goes back up. The Horz. >> > derived voltage come up for a moment but go right back down, which > means >> > its >> > trying to start.I'm wondering if my orginal 157 volts is too high? I > got >> > to >> > change a few of the (required) caps yet but would anyone have any tips > on >> > this one. >> > >> > Buck Pasher >> > Buck's TV >> > Gander Newfoundland >> > Canada >> > 709-256-7738 (Fax & Phone) >> > >> > >> > >> > >> > >> -------------------------------------------------------------------------- > --- >> > Lost Password: >> > http://www.tech-assist.org and select "Login Problems?". >> > Email Archives: >> > //www.freelists.org/archives/techassist/ >> > >> > >> >> >> >> -------------------------------------------------------------------------- > --- >> Lost Password: >> http://www.tech-assist.org and select "Login Problems?". >> Email Archives: >> //www.freelists.org/archives/techassist/ >> >> >> >> >> >> >> >> -------------------------------------------------------------------------- > --- >> Lost Password: >> http://www.tech-assist.org and select "Login Problems?". >> Email Archives: >> //www.freelists.org/archives/techassist/ >> > > > ----------------------------------------------------------------------------- > Lost Password: > http://www.tech-assist.org and select "Login Problems?". > Email Archives: > //www.freelists.org/archives/techassist/ > > ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/