[SI-LIST] Re: HDMI Frequency Failing RE Test by 7dB!!!!
- From: vinod ah <ah.vinod@xxxxxxxxx>
- To: Ken Wyatt <ken@xxxxxxxxxxxxxxxx>
- Date: Wed, 23 May 2012 21:11:31 +0530
Hi Ken,
I just checked the layout and found that there are four pins for
connecting the shield pins to ground and we have used a zero ohms
between shield pin and ground. Is this ok to do so or should i have
solid ground connection to the shield pins. Also if i replace the zero
ohms with ferrite bead, will it help?
Regards
Vinod A H
On Wed, May 23, 2012 at 8:56 PM, Ken Wyatt <ken@xxxxxxxxxxxxxxxx> wrote:
> Vinod,
>
> Is the HDMI connector shield -directly- connected to the (metallic)
> enclosure? This should ideally be multiple connections. If the shield is
> floating or poorly connected, you'll get common-mode currents flowing along
> the outside of the HDMI cable shield.
>
> Have you measured the common-mode currents with a current probe?
> _______________________
> Kenneth Wyatt
> Wyatt Technical Services LLC
> Woodland Park, CO
> Email Me! | Web Site | Blog
> Subscribe to Newsletter
> Connect with me on LinkedIn
>
> On May 23, 2012, at 9:17 AM, vinod ah wrote:
>
> Hi Vijay,
>
> We have option to control the current and voltage swing. We tried
> both, without violating eye test, but still the i am seeing radiation
> at 742.5MHz. The radiation level keeps chnaging as i try with multiple
> cables. I found the best cable i had to be failing FCC limits by 7dB.
> I used some HDMI cable which are sold by big brands, but i was failing
> FCC by 12dB !!!.
>
> Hi Boris,
>
> We tested the Blu ray player and TV with same HDMI cable used for our
> board testing. the Blu ray player used is from Sony while the TV is
> from LG, we connected the blu ray player to TV using same HDMI cable
> and took the readings.
>
> Regards
> Vinod A H
>
> On Wed, May 23, 2012 at 8:43 PM, Traa, Boris <boris.traa@xxxxxxxxxxx> wrote:
>
> Dear Venod,
>
>
> You said that TV is oke and Blu Ray is tested. Seperately or as a
> combination with the same cables you also used to attach your board?
>
>
> Kind regards
>
> Boris Traa
>
> System design engineer EMC
>
>
> It's the currents that make circuits work or fail.
>
>
> Philips Innovation Services/EMC center
>
> Room 2.020
>
> High Tech Campus 26
>
> 5656AE Eindhoven, The Netherlands
>
> Tel: ++ 31 40 27 43766
>
> Fax: ++ 31 40 27 42224
>
> E-mail: boris.traa@xxxxxxxxxxx
>
>
>
> -----Original Message-----
>
> From: si-list-bounce@xxxxxxxxxxxxx [mailto:si-list-bounce@xxxxxxxxxxxxx] On
> Behalf Of vinod ah
>
> Sent: Wednesday 23 May 2012 3:58 PM
>
> To: SI-LIST
>
> Subject: [SI-LIST] HDMI Frequency Failing RE Test by 7dB!!!!
>
>
> Hi All,
>
>
> I am designing a board with HDMI input and HDMI output. I am facing EMI
> issue at 742.5MHz (failing FCC limits by 7dB) when running 1080p30 on both
> Input and output HDMI i.e. BLu ray player connected to HDMI input connector
> of my board is giving out data at 1080p30 and HDMI out of my board is
> connected to TV which is also 1080p30 content. So i am unable to find out
> how is 742.5MHz coming out as radiation as it is 10th Harmonic of pixel
> clock 74.25MHz!!!!!!!. I am not facing any issues with other harmonics
> except for this. So i am totally confused on how to go about debugging this
> issue.
>
>
> Note: All the signals are routed on top layer without vias and all signals
> have solid ground plane reference. The blu ray player and TV used, is tested
> for radiation and no significant levels seen.
>
>
> Regards
>
> Vinod A H
>
> ------------------------------------------------------------------
>
> To unsubscribe from si-list:
>
> si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
>
>
> or to administer your membership from a web page, go to:
>
> //www.freelists.org/webpage/si-list
>
>
> For help:
>
> si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
>
>
>
> List forum is accessible at:
>
> http://tech.groups.yahoo.com/group/si-list
>
>
> List archives are viewable at:
>
> //www.freelists.org/archives/si-list
>
>
> Old (prior to June 6, 2001) list archives are viewable at:
>
> http://www.qsl.net/wb6tpu
>
>
>
>
> ________________________________
>
> The information contained in this message may be confidential and legally
> protected under applicable law. The message is intended solely for the
> addressee(s). If you are not the intended recipient, you are hereby notified
> that any use, forwarding, dissemination, or reproduction of this message is
> strictly prohibited and may be unlawful. If you are not the intended
> recipient, please contact the sender by return e-mail and destroy all copies
> of the original message.
>
>
> ------------------------------------------------------------------
> To unsubscribe from si-list:
> si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
>
> or to administer your membership from a web page, go to:
> //www.freelists.org/webpage/si-list
>
> For help:
> si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
>
>
> List forum is accessible at:
> http://tech.groups.yahoo.com/group/si-list
>
> List archives are viewable at:
> //www.freelists.org/archives/si-list
>
> Old (prior to June 6, 2001) list archives are viewable at:
> http://www.qsl.net/wb6tpu
>
>
>
------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
or to administer your membership from a web page, go to:
//www.freelists.org/webpage/si-list
For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
List forum is accessible at:
http://tech.groups.yahoo.com/group/si-list
List archives are viewable at:
//www.freelists.org/archives/si-list
Old (prior to June 6, 2001) list archives are viewable at:
http://www.qsl.net/wb6tpu
Other related posts:
