Too bad. Al --- Terry Lane <tel@xxxxxxxxxxx> wrote: > No Al, not much clay around here at all. Limestone, > talc, ironstone, but no > clay. > > > > > > No suitable Clay in the banks of that creek that > flows > > through your rancho?? > > > > Al Messer > > --- Terry Lane <tel@xxxxxxxxxxx> wrote: > > > > > Just sent you a couple - I'll try & get a couple > of > > > the lil gas bottle jobby > > > later today > > > > > > Well I did have to (shudder) buy the refractory. > > > Finally tracked it down > > > locally at a potter's supply house, who have all > > > sorts of good things for > > > establishing a foundry. Bentonite for making > > > greensand, fireclay, and I also > > > (wince) bought some porcelain clay to experiment > > > with making crucibles. AND > > > the nice lady in charge over there has offered > to > > > fire the crucibles for me > > > when I get 'em made. > > > > > > > > > > > > > > > > Tel > > > > > > > > Thanks, would love a pic or two. > > > > > > > > Peter > > > > > > > > PS Why am I not surprised you didn't buy an > off > > > the shelf jobbie? > > > > > > > > ----- Original Message ----- > > > > From: "Terry Lane" <tel@xxxxxxxxxxx> > > > > To: <modeleng@xxxxxxxxxxxxx> > > > > Sent: Sunday, October 17, 2004 9:07 PM > > > > Subject: [modeleng] Re: Melting Down - > Smelting > > > > > > > > > > > > I've recenjtly built two furnaces Peter, one > is > > > based on a section of 12" > > > > diameter water heater barrel - 15" high with a > 2 > > > 1/2" lining of castable > > > > refractory, it works real well on charcoal and > (at > > > a pinch) wood chips. > > > The > > > > second is based on a 5lb gas bottle - similar > > > construction but with the > > > > 'blow hole' a bit higher up for gas firing - > > > haven't really fired it yet, > > > > other than to cure the refractory & 'tune' the > gas > > > burner. > > > > > > > > For reclaming scrap and some aluminium work I > > > still use the forge (wheel > > > rim > > > > welded to a 12 gal drum with air system > > > underneath) - air supply for both > > > > solid fuel furnaces, is an Electrolux vacuum > > > cleaner with the hgose > > > attached > > > > to the 'blow side' > > > > > > > > I'll send you a pic or two if you like > > > > > > > > ----- Original Message ----- > > > > From: "Peter J. Cathcart" > > > <peter.cathcart@xxxxxxxxxxxxx> > > > > To: <modeleng@xxxxxxxxxxxxx> > > > > Sent: Monday, October 18, 2004 5:58 AM > > > > Subject: [modeleng] Melting Down - Smelting > > > > > > > > > > > > > Tel and all > > > > > > > > > > Your comment below struck a cord. I just > missed > > > a small smelter on eBay > > > > > yesterday (sorry Tel, nearly spent money). > I > > > have wanted a small > > > smelting > > > > > device for some time. Lead, copper and > brass > > > probably figure most in > > > > terms > > > > > of what I would use it for. Trying to find > a > > > suitable device however is > > > > not > > > > > so easy. > > > > > > > > > > So how does everyone out there deal with > > > smelting? What devices are > > > > > available? What problems arise? > > > > > > > > > > Peter > > > > > > > > > > -------- > > > > > You should get a few bits n pieces worth > saving > > > and a bit of aluminium > > > for > > > > > melting down, > > > > > > > > > > > > > > > > > > > > > > > > > MODEL ENGINEERING DISCUSSION LIST. > > > > > > > > > > To UNSUBSCRIBE from this list, send a blank > > > email to, > > > > > modeleng-request@xxxxxxxxxxxxx with the word > > > "unsubscribe" in the > > > subject > > > > line. > > > > > > > > > > > > > MODEL ENGINEERING DISCUSSION LIST. > > > > > > > > To UNSUBSCRIBE from this list, send a blank > email > > > to, > > > > modeleng-request@xxxxxxxxxxxxx with the word > > > "unsubscribe" in the subject > > > > line. > > > > > > > > > > > > > > > > MODEL ENGINEERING DISCUSSION LIST. > > > > > > > > To UNSUBSCRIBE from this list, send a blank > email > > > to, > > > > modeleng-request@xxxxxxxxxxxxx with the word > > > "unsubscribe" in the subject > > > line. > > > > > > > > > > MODEL ENGINEERING DISCUSSION LIST. > > > > > > To UNSUBSCRIBE from this list, send a blank > email > > > to, > > > modeleng-request@xxxxxxxxxxxxx with the word > > > "unsubscribe" in the subject line. > > > > > > > > > > > > > __________________________________ > > Do you Yahoo!? > > Yahoo! Mail - Helps protect you from nasty > viruses. > > http://promotions.yahoo.com/new_mail > > MODEL ENGINEERING DISCUSSION LIST. > > > > To UNSUBSCRIBE from this list, send a blank email > to, > > modeleng-request@xxxxxxxxxxxxx with the word > "unsubscribe" in the subject > line. > > > > MODEL ENGINEERING DISCUSSION LIST. > > To UNSUBSCRIBE from this list, send a blank email > to, > modeleng-request@xxxxxxxxxxxxx with the word > "unsubscribe" in the subject line. > __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com MODEL ENGINEERING DISCUSSION LIST. To UNSUBSCRIBE from this list, send a blank email to, modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the subject line.