[minima] Re: Ver.0.030 code problems
- From: <jerry@xxxxxxxxxxxxxxxx>
- To: minima@xxxxxxxxxxxxx
- Date: Sun, 30 Mar 2014 01:09:58 -0700
Go To: //www.freelists.org/archive/minima
On the right top of the page click on "Manage my subscription"
It will take you to a page that on the bottom left it says "options" put
in your email address , pull down the arrow, select unsubscribe. Jerry
K5LRU
Harwood, Texas
> -------- Original Message --------
> Subject: [minima] Re: Ver.0.030 code problems
> From: "Clyde Hyman" <zs1cs@xxxxxxxxxxxx>
> Date: Sun, March 30, 2014 2:55 am
> To: <minima@xxxxxxxxxxxxx>
>
>
> Please how can I unsubscribe to minima groups, I am having problems with my
> Email hanging up.
> Thank you.
> Clyde ZS1CS
> ----- Original Message -----
> From: Frank
> To: minima@xxxxxxxxxxxxx
> Sent: Saturday, March 29, 2014 7:52 PM
> Subject: [minima] Re: Ver.0.030 code problems
>
>
> Jerry,
>
> I use a Mac, you know I believe Thomas also uses a Mac. I wonder if you
> have hit on something.
>
>
> Frank - W4NHJ
>
> -
> On 3/29/14, 1:14 PM, jerry@xxxxxxxxxxxxxxxx wrote:
>
> Frank, thanks for sending the files, I will compare the code to mine.
> What operating system do you run your Arduino software with? Jerry
>
> K5LRU
> Harwood, Texas
>
> -------- Original Message --------
> Subject: [minima] Re: Ver.0.030 code problems
> From: Frank <w4nhj@xxxxxxxxxxx>
> Date: Sat, March 29, 2014 11:03 am
> To: minima@xxxxxxxxxxxxx
>
>
> Jerry,
>
> I tested my digital board with the V0.03 firmware and it works. I could
> send you the three files I have and you can see if that works. Perhaps
> something was changed in the firmware that is on Github now, but I doubt it.
>
> Frank - W4NHJ
>
> -
> On 3/29/14, 11:34 AM, Celso - PY2XT wrote:
> Hi Jerry and folks,
>
> I have the same problem with my digital board, just like you.
>
> I will continue researching and wait for help from more experienced friends.
>
> 73 to all.
>
> Celso - PY2XT.
>
>
> De: jerry@xxxxxxxxxxxxxxxx
> Enviada: Sábado, 29 de Março de 2014 07:02
> Para: minima@xxxxxxxxxxxxx
> Assunto: [minima] Ver.0.030 code problems
>
> I bought a new si570, built a new digi-board, and guess what, I still
> have the same problem. The si570 is frozen at 56.3 Mhz. I got a test
> sketch from Mac (I put my callsign in the code to make sure I was
> pulling up the right file through Arduino) see attachment, and I am able
> to change the frequency of the si570 with the sketch which proves the
> I2C bus is working OK. The chip puts out a clean signal at around 2.84v
> peak to peak, (see attachments). With Farhan's original sketch, the
> si570 will tune. I think I've read everything there is on the internet
> about the I2C buss, and I don't think that's my problem, unless it is
> running too fast with the new version code. I made my own digi board
> pcb, but it was from Adrian's design, so it should be the same as
> everyone else. The voltages on the si570 are at 3.274. I'm out of ideas.
> I need help. Jerry
>
> K5LRU
> Harwood, Texas
>
>
>
>
>
>
>
> ---
> This email is free from viruses and malware because avast! Antivirus
> protection is active.
> http://www.avast.com
Other related posts:
