No problem Adrian Very good job making the pcbs , thanks. EA7KB > From: jerry@xxxxxxxxxxxxxxxx > To: minima@xxxxxxxxxxxxx > Subject: [minima] Re: Resistor in main board pcb > Date: Wed, 5 Feb 2014 12:14:10 -0700 > > Don't feel bad Adrian, I missed it too, and I did a parts count, three > times. The first time I came up one short, but a second and third count > came out right. That's why it's always good to build one board before > ordering a bunch. But everybody is excited to build this neat little > transceiver. I hope that's all we missed. Jerry > > K5LRU > Harwood, Texas > > > -------- Original Message -------- > > Subject: [minima] Re: Resistor in main board pcb > > From: Adrian Preda <ady.preda@xxxxxxxxx> > > Date: Wed, February 05, 2014 12:43 pm > > To: "minima@xxxxxxxxxxxxx" <minima@xxxxxxxxxxxxx> > > > > > > Hi group, > > > > Shame for me I left that resistor out of he pcb...I simply forgot about it. > > > > A solution can be by placing the 4k7 (or 47k) instead of that jumper on > > digital board. But, in this way, pins T/R becomes PTT, and viceversa. It > > can be a solution without scratching the PCB. > > > > @Sandeep, I was very busy this days with work, I couldn't reply in time to > > your remarks regarding PCB production. I read now all the post, and see > > you managed to make the masking ok. If you need anything I will help you > > asap. > > > > Adrian > > YO4HHP > > > > > > ________________________________ > > From: Sandeep Lohia <sandeeplohia12@xxxxxxxxx> > > To: minima@xxxxxxxxxxxxx > > Sent: Wednesday, February 5, 2014 5:56 PM > > Subject: [minima] Re: Resistor in main board pcb > > > > > > M bit confused abt 47k or 4K7, till I have PCB in my hand... > > > > anyways thanks 4 correction note... > > > > On 05/02/2014, Sandeep Lohia <sandeeplohia12@xxxxxxxxx> wrote: > > > We might skip this cutting also (see attachment) > > > > > > By installing 4.7 K inside Header connector wire ( wire which connects > > > both boards) See T/R or PTT. > > > > > > > > > > > > > > > > > > On 05/02/2014, Leonardo Ramirez <ea7kb@xxxxxxxxxxx> wrote: > > >> I had to add a 47k resistor and works well, with 4.7k with the Atmel > > >> remained in TX. > > >> > > >> 73. > > >> > > >> > > >>> Date: Wed, 5 Feb 2014 20:53:16 +0530 > > >>> Subject: [minima] Re: Resistor in main board pcb > > >>> From: sandeeplohia12@xxxxxxxxx > > >>> To: minima@xxxxxxxxxxxxx > > >>> > > >>> Thanks Leo -EA7KB > > >>> > > >>> There's a jumper on PIN 5 of Arduino (digital board), hope we can > > >>> replace jumper with 4.7K resistance (only if PTT still works)... > > >>> > > >>> Otherwise we need to cut a small trace ( with surgical hobby knife or > > >>> shaving blade) scratch remove green-solder-resist-mask & install 4.7 K > > >>> on back side of MAIN PCB. > > >>> > > >>> > > >>> > > >>> On 05/02/2014, Leonardo Ramirez <ea7kb@xxxxxxxxxxx> wrote: > > >>> > Hi guys. > > >>> > In Main board pcb must be added the base resistance of q23 . > > >>> > Regards. > > >>> > > > >>> > Leo / EA7KB > > >>> > > > >>> > > > >>> > > > >>> > > >>> > > >>> -- > > >>> -- > > >>> Please encourage recycling, reuse or repairing of E-waste. > > >>> ░7░3░ ░d░e░ ░V░U░3░S░X░T░ > > > > >>> > > >> > > > > > > > > > -- > > > -- > > > Please encourage recycling, reuse or repairing of E-waste. > > > ░7░3░ ░d░e░ ░V░U░3░S░X░T░ > > > > > > > > > -- > > -- > > Please encourage recycling, reuse or repairing of E-waste. > > ░7░3░ ░d░e░ ░V░U░3░S░X░T░ >