[PCB_FORUM] Re: Netlist from Orcad(cadence)
- From: Shahed.Safavi-Bayat@xxxxxxxxxxxxxxxxxxxxx
- To: icu-pcb-forum@xxxxxxxxxxxxx
- Date: Wed, 25 Jan 2012 14:31:44 -0500
Unfortunately Power net is not working with 16.xx.
Shahed
From:
"Khurana, Varun" <vkhurana@xxxxxxxxxxxx>
To:
"icu-pcb-forum@xxxxxxxxxxxxx" <icu-pcb-forum@xxxxxxxxxxxxx>
Date:
01/25/2012 02:27 PM
Subject:
[PCB_FORUM] Re: Netlist from Orcad(cadence)
You can pass attributes too using the PowerNET netlister – details are at
http://pcbstandards.com/forums/showthread.php?p=8612
Varun
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx [
mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of
Shahed.Safavi-Bayat@xxxxxxxxxxxxxxxxxxxxx
Sent: Wednesday, January 25, 2012 8:53 AM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Netlist from Orcad(cadence)
Sam,
As already was pointed out by another member OrCAD can out put .asc file
but the net list that OrCAD generate is void of any attributes from
schematic. Also footprint names should be same as their PADS footprints
library. To do this go to net list dialog box and select other and in
their you have
two netlister for PADS.
Good Luck!
Shahed
From:
sjchar3@xxxxxxxxxxxx
To:
icu-pcb-forum@xxxxxxxxxxxxx
Date:
01/25/2012 11:21 AM
Subject:
[PCB_FORUM] Re: Netlist from Orcad(cadence)
Group:
The other group requested all our Cadence files for a particular board.
They use PADs and requested a netlist file.
I know orcad creates .dat files, I'm asking can these files be used to
create a .pcb file?
Is the DSN file sufficient?
I don't much about PADs, hopefully someone here can help. We have Cadence,
they have PADs.
Thanks again,
Sam
-----Original Message-----
From: David Price <davidp@xxxxxxxxxxxxxx>
To: icu-pcb-forum <icu-pcb-forum@xxxxxxxxxxxxx>
Sent: Wed, Jan 25, 2012 8:33 am
Subject: [PCB_FORUM] Re: Netlist from Orcad(cadence)
Yes, Capture formatted netlist can be used as a schemaic frontend to PADs.
Capture is often the schematic preferred choice for PADs users.
David
At 10:05 AM 1/25/2012, you wrote:
Group, Can I use the netlist from Orcad and import into pads?
I'm using Cadence 16.3 and our other site is using Mentor's PADs.
Thanks,
Sam
NOTICE
If you are not the intended recipient, please contact the sender by reply
e-mail and destroy the original message and any copy of the message as
well as any attachment to the original message. This e-mail message and
any attachment are for the sole use of the intended recipients and may
contain proprietary and/or confidential information which may be
privileged or otherwise protected from disclosure. Any unauthorized
review, use, disclosure or distribution is prohibited without prior
authorization by SAFRAN-ELECTRONICS CANADA. An e-mail response to this
address may be subject to interception or monitoring for operational
reasons or for lawful business practices. SAFRAN-ELECTRONICS CANADA shall
not therefore be liable in any way for the message if modified, altered or
falsified.
Safran-Electronics Canada
(formerly Hispano-Suiza Canada)
www.Safran-Electronics.ca
NOTICE
If you are not the intended recipient, please contact the sender by reply
e-mail and destroy the original message and any copy of the message as
well as any attachment to the original message. This e-mail message and
any attachment are for the sole use of the intended recipients and may
contain proprietary and/or confidential information which may be
privileged or otherwise protected from disclosure. Any unauthorized
review, use, disclosure or distribution is prohibited without prior
authorization by SAFRAN-ELECTRONICS CANADA. An e-mail response to this
address may be subject to interception or monitoring for operational
reasons or for lawful business practices. SAFRAN-ELECTRONICS CANADA shall
not therefore be liable in any way for the message if modified, altered or
falsified.
Safran-Electronics Canada
(formerly Hispano-Suiza Canada)
www.Safran-Electronics.ca
Other related posts:
