Jack, I am unable to replicate the particular problem you have printing to file. - Peter -----Original Message----- From: duxhelp-bounce@xxxxxxxxxxxxx [mailto:duxhelp-bounce@xxxxxxxxxxxxx] On Behalf Of Jack Maartman Sent: Friday, May 28, 2004 11:49 PM To: duxhelp@xxxxxxxxxxxxx Subject: [duxhelp] Re: For Autobuild users only. Is it possible to "print to file," using no page numbers, no form feeds and a <cr> as (eol) character? Whenever I try this I get the message error in line -1. Jack ----- Original Message ----- From: "Jack Maartman" <jmaartman@xxxxxxxxxxx> To: <duxhelp@xxxxxxxxxxxxx> Sent: Friday, May 28, 2004 8:17 PM Subject: [duxhelp] Re: For Autobuild users only. > Same behaviour in the beta more or less, however the default number of > lines for 10 inch 22 twenty-two, I think. The top margin still reverts 10 in > 2,0 12 in 1,0. > > ----- Original Message ----- > From: "George Bell" <george@xxxxxxxxxxxxxxxxxxx> > To: <duxhelp@xxxxxxxxxxxxx> > Sent: Friday, May 28, 2004 4:56 PM > Subject: [duxhelp] For Autobuild users only. > > > > If you are not on the Untested Autobuild access list, and if you have a > > build earlier than 28th May, please ignore this message. > > > > If you DO have the autobuild of 18th May or later, I really would be > > grateful if you could PLEASE take a few minutes to try these steps. > > > > 1) Go to Global Embosser Setup. > > > > 2) Select "New". > > > > 3) In the General Tab, where it now says, "(Please select a model)", > > scroll down and select "Freedom Scientific Braille Blazer". > > > > 4) Click on OK. (Which will return you to the main dialog. > > > > 5) If you happen to have other embossers set up, is the highlight on, > > "Freedom Scientific Braille Blazer", or something else? In my case, > > focus seems to be always on the SECOND in the list, NOT on the newly > > created Device. > > > > 6) Highlight the new device anyway. Does Form go to "Narrow Width, 10 > > Inch Long, Braille Paper"? > > > > 7) Regardless of above, note setting of Lines per page. 10 inch shows > > 24 Lines. > > > > 8) Now look at Top Margin, which should be zero, and enter a figure of > > two, and click O.K. > > > > 9) A warning comes up. Does it say, "Old Format" 2, and "New Format" > > zero? > > > > 10) Click OK to accept, and return to DBT. > > > > 11) Go back to Global Embosser Setup, select the above embosser, and > > tell me what the Top Margin is set to? (Remember, we entered "2" > > previously. On my system it comes back as Zero. > > > > Fine, but we're not finished yet. > > > > 12) With the above embosser selected, change the form to, "Narrow > > Width, 12 inch Long, Braille Paper" > > > > 13) Note that Lines per page is now 28, and that we have a Top Margin > > of Zero. > > > > 14) Change Top Margin in Lines from Zero again to 2, and press OK. > > > > 15) Warning comes up. Is it Old Format 2 - New Format 1? Click on OK. > > Dialog closes. > > > > 16) Back into embosser Setup again and select the same Device. Is > > Lines per page still 28, and has Top Margin become 1 (One)? But did we > > not enter 2? > > > > Now I have done this on two separate downloads, and on two separate > > machines and operating systems (XP Home and Pro) and I get the same > > results. > > > > George Bell. > > > > > > > > > > > > > > > > > > > > This Message has been scanned for viruses by McAfee Groupshield. > > * * * > > * This message is via list duxhelp at freelists.org. > > * To unsubscribe, send a blank message with > > * unsubscribe > > * as the subject to <duxhelp-request@xxxxxxxxxxxxx>. You may also > > * subscribe, unsubscribe, and set vacation mode and other subscription > > * options by visiting //www.freelists.org. The list archive > > * is also located there. > > * Duxbury Systems' web site is http://www.duxburysystems.com > > * * * > > * * * > * This message is via list duxhelp at freelists.org. > * To unsubscribe, send a blank message with > * unsubscribe > * as the subject to <duxhelp-request@xxxxxxxxxxxxx>. You may also > * subscribe, unsubscribe, and set vacation mode and other subscription > * options by visiting //www.freelists.org. The list archive > * is also located there. > * Duxbury Systems' web site is http://www.duxburysystems.com > * * * * * * * This message is via list duxhelp at freelists.org. * To unsubscribe, send a blank message with * unsubscribe * as the subject to <duxhelp-request@xxxxxxxxxxxxx>. You may also * subscribe, unsubscribe, and set vacation mode and other subscription * options by visiting //www.freelists.org. The list archive * is also located there. * Duxbury Systems' web site is http://www.duxburysystems.com * * * * * * * This message is via list duxhelp at freelists.org. * To unsubscribe, send a blank message with * unsubscribe * as the subject to <duxhelp-request@xxxxxxxxxxxxx>. You may also * subscribe, unsubscribe, and set vacation mode and other subscription * options by visiting //www.freelists.org. The list archive * is also located there. * Duxbury Systems' web site is http://www.duxburysystems.com * * *