[duxhelp] Re: For Autobuild users only.
- From: "Jack Maartman" <jmaartman@xxxxxxxxxxx>
- To: <duxhelp@xxxxxxxxxxxxx>
- Date: Fri, 28 May 2004 20:48:49 -0700
Is it possible to "print to file," using no page numbers, no form feeds and
a <cr> as (eol) character? Whenever I try this I get the message error in
line -1.
Jack
----- Original Message -----
From: "Jack Maartman" <jmaartman@xxxxxxxxxxx>
To: <duxhelp@xxxxxxxxxxxxx>
Sent: Friday, May 28, 2004 8:17 PM
Subject: [duxhelp] Re: For Autobuild users only.
> Same behaviour in the beta more or less, however the default number of
> lines for 10 inch 22 twenty-two, I think. The top margin still reverts 10
in
> 2,0 12 in 1,0.
>
> ----- Original Message -----
> From: "George Bell" <george@xxxxxxxxxxxxxxxxxxx>
> To: <duxhelp@xxxxxxxxxxxxx>
> Sent: Friday, May 28, 2004 4:56 PM
> Subject: [duxhelp] For Autobuild users only.
>
>
> > If you are not on the Untested Autobuild access list, and if you have a
> > build earlier than 28th May, please ignore this message.
> >
> > If you DO have the autobuild of 18th May or later, I really would be
> > grateful if you could PLEASE take a few minutes to try these steps.
> >
> > 1) Go to Global Embosser Setup.
> >
> > 2) Select "New".
> >
> > 3) In the General Tab, where it now says, "(Please select a model)",
> > scroll down and select "Freedom Scientific Braille Blazer".
> >
> > 4) Click on OK. (Which will return you to the main dialog.
> >
> > 5) If you happen to have other embossers set up, is the highlight on,
> > "Freedom Scientific Braille Blazer", or something else? In my case,
> > focus seems to be always on the SECOND in the list, NOT on the newly
> > created Device.
> >
> > 6) Highlight the new device anyway. Does Form go to "Narrow Width, 10
> > Inch Long, Braille Paper"?
> >
> > 7) Regardless of above, note setting of Lines per page. 10 inch shows
> > 24 Lines.
> >
> > 8) Now look at Top Margin, which should be zero, and enter a figure of
> > two, and click O.K.
> >
> > 9) A warning comes up. Does it say, "Old Format" 2, and "New Format"
> > zero?
> >
> > 10) Click OK to accept, and return to DBT.
> >
> > 11) Go back to Global Embosser Setup, select the above embosser, and
> > tell me what the Top Margin is set to? (Remember, we entered "2"
> > previously. On my system it comes back as Zero.
> >
> > Fine, but we're not finished yet.
> >
> > 12) With the above embosser selected, change the form to, "Narrow
> > Width, 12 inch Long, Braille Paper"
> >
> > 13) Note that Lines per page is now 28, and that we have a Top Margin
> > of Zero.
> >
> > 14) Change Top Margin in Lines from Zero again to 2, and press OK.
> >
> > 15) Warning comes up. Is it Old Format 2 - New Format 1? Click on OK.
> > Dialog closes.
> >
> > 16) Back into embosser Setup again and select the same Device. Is
> > Lines per page still 28, and has Top Margin become 1 (One)? But did we
> > not enter 2?
> >
> > Now I have done this on two separate downloads, and on two separate
> > machines and operating systems (XP Home and Pro) and I get the same
> > results.
> >
> > George Bell.
> >
> >
> >
> >
> >
> >
> >
> >
> >
> > This Message has been scanned for viruses by McAfee Groupshield.
> > * * *
> > * This message is via list duxhelp at freelists.org.
> > * To unsubscribe, send a blank message with
> > * unsubscribe
> > * as the subject to <duxhelp-request@xxxxxxxxxxxxx>. You may also
> > * subscribe, unsubscribe, and set vacation mode and other subscription
> > * options by visiting //www.freelists.org. The list archive
> > * is also located there.
> > * Duxbury Systems' web site is http://www.duxburysystems.com
> > * * *
>
> * * *
> * This message is via list duxhelp at freelists.org.
> * To unsubscribe, send a blank message with
> * unsubscribe
> * as the subject to <duxhelp-request@xxxxxxxxxxxxx>. You may also
> * subscribe, unsubscribe, and set vacation mode and other subscription
> * options by visiting //www.freelists.org. The list archive
> * is also located there.
> * Duxbury Systems' web site is http://www.duxburysystems.com
> * * *
* * *
* This message is via list duxhelp at freelists.org.
* To unsubscribe, send a blank message with
* unsubscribe
* as the subject to <duxhelp-request@xxxxxxxxxxxxx>. You may also
* subscribe, unsubscribe, and set vacation mode and other subscription
* options by visiting //www.freelists.org. The list archive
* is also located there.
* Duxbury Systems' web site is http://www.duxburysystems.com
* * *
Other related posts:
