Same behaviour in the beta more or less, however the default number of lines for 10 inch 22 twenty-two, I think. The top margin still reverts 10 in 2,0 12 in 1,0. ----- Original Message ----- From: "George Bell" <george@xxxxxxxxxxxxxxxxxxx> To: <duxhelp@xxxxxxxxxxxxx> Sent: Friday, May 28, 2004 4:56 PM Subject: [duxhelp] For Autobuild users only. > If you are not on the Untested Autobuild access list, and if you have a > build earlier than 28th May, please ignore this message. > > If you DO have the autobuild of 18th May or later, I really would be > grateful if you could PLEASE take a few minutes to try these steps. > > 1) Go to Global Embosser Setup. > > 2) Select "New". > > 3) In the General Tab, where it now says, "(Please select a model)", > scroll down and select "Freedom Scientific Braille Blazer". > > 4) Click on OK. (Which will return you to the main dialog. > > 5) If you happen to have other embossers set up, is the highlight on, > "Freedom Scientific Braille Blazer", or something else? In my case, > focus seems to be always on the SECOND in the list, NOT on the newly > created Device. > > 6) Highlight the new device anyway. Does Form go to "Narrow Width, 10 > Inch Long, Braille Paper"? > > 7) Regardless of above, note setting of Lines per page. 10 inch shows > 24 Lines. > > 8) Now look at Top Margin, which should be zero, and enter a figure of > two, and click O.K. > > 9) A warning comes up. Does it say, "Old Format" 2, and "New Format" > zero? > > 10) Click OK to accept, and return to DBT. > > 11) Go back to Global Embosser Setup, select the above embosser, and > tell me what the Top Margin is set to? (Remember, we entered "2" > previously. On my system it comes back as Zero. > > Fine, but we're not finished yet. > > 12) With the above embosser selected, change the form to, "Narrow > Width, 12 inch Long, Braille Paper" > > 13) Note that Lines per page is now 28, and that we have a Top Margin > of Zero. > > 14) Change Top Margin in Lines from Zero again to 2, and press OK. > > 15) Warning comes up. Is it Old Format 2 - New Format 1? Click on OK. > Dialog closes. > > 16) Back into embosser Setup again and select the same Device. Is > Lines per page still 28, and has Top Margin become 1 (One)? But did we > not enter 2? > > Now I have done this on two separate downloads, and on two separate > machines and operating systems (XP Home and Pro) and I get the same > results. > > George Bell. > > > > > > > > > > This Message has been scanned for viruses by McAfee Groupshield. > * * * > * This message is via list duxhelp at freelists.org. > * To unsubscribe, send a blank message with > * unsubscribe > * as the subject to <duxhelp-request@xxxxxxxxxxxxx>. You may also > * subscribe, unsubscribe, and set vacation mode and other subscription > * options by visiting //www.freelists.org. The list archive > * is also located there. > * Duxbury Systems' web site is http://www.duxburysystems.com > * * * * * * * This message is via list duxhelp at freelists.org. * To unsubscribe, send a blank message with * unsubscribe * as the subject to <duxhelp-request@xxxxxxxxxxxxx>. You may also * subscribe, unsubscribe, and set vacation mode and other subscription * options by visiting //www.freelists.org. The list archive * is also located there. * Duxbury Systems' web site is http://www.duxburysystems.com * * *