Many thanks once again Dean. David Sent from my iPad > On 18 Feb 2014, at 17:17, Dean Wilcox <wilcoxdean@xxxxxxxxxxx> wrote: > > Hi, > After you have pressed the button and read the time it is not necesary to > press it again, it disables itself, I think after ten seconds. > Once you have pulled the button out slightly to set the time, that's when you > change both the hands and vibrations together the watch won't set the time > until you push the button back in. So it could be 16:54, you could set your > watch to 17:00 and on the dot you could press the button in and it will then > set. > As for syncing the hands, they must be set to midnight. I can't remember if > I set the vibrations to midnight first or whether this was done automatically > when you sync the hands so sorry on that. There are points on the face to > move the hands forward or back to get them to midnight but you do need to see > to set this. However, mine have never gone out of sync which may be good for > you to know. > > Dean > > > >> On 18 Feb 2014, at 10:05, David Halliwell <davidpeterhalliwell@xxxxxxxxx> >> wrote: >> >> Hi Dean, >> Thanks so much for your email; and what a quick response! >> I like the watch so far anyway, but have a couple of questions you may be >> able to help with: >> After you've read the time, is it necessary to press the button to disable >> the mechanism, or does this happen automatically; >> When I'm setting the time, is this only active when the button is pressed >> following the positioning of the hands, for example, can I set the watch to >> midnight and then wait until Big Ben strikes and then press the button then >> to set this from that point; >> And finally, in terms of synchronising the hands, this sounds really >> complicated, and I'm not really getting it to be honest, can you shed any >> light on this - I'm also a bit concerned as the instructions say you need to >> be able to see to do this, and I'm a total. >> Thanks in advance for any answers you can help with. >> David >> >> >> Sent from my iPad >> >>> On 17 Feb 2014, at 22:54, Dean Wilcox <wilcoxdean@xxxxxxxxxxx> wrote: >>> >>> Just to add, I also have one of these, have had mine for over four years. >>> It seems as though there are a few users of this watch around so posting to >>> the list or emailing one or two of us privately should get your questions >>> answered nice and fast. >>> >>> Enjoy, I like this watch! >>> >>> Dean >>> >>> >>>> On 17 Feb 2014, at 22:05, RMPortal <robertmartin.portal@xxxxxx> wrote: >>>> >>>> David, I have one of these watches. If you've managed to set it up you've >>>> probably worked out most of what you need to know. Let me know if there's >>>> something in particular like alarm settings you want to know about and I'll >>>> try my best. >>>> >>>> I haven't needed to myself but you might find something on the Tissot >>>> website. >>>> >>>> Best wishes >>>> >>>> Robert >>>> >>>> -----Messaggio originale----- >>>> Da: access-uk@xxxxxxxxxxxxx [mailto:access-uk@xxxxxxxxxxxxx] Per conto di >>>> David Halliwell >>>> Inviato: lunedì 17 febbraio 2014 22.47 >>>> A: access-uk@xxxxxxxxxxxxx >>>> Oggetto: [access-uk] Vibrating tactile watch query >>>> >>>> Hello, >>>> I received a Tissot silen-t watch for my Birthday this weekend. >>>> I understand the RNIB used to sell this watch, and I was wondering on the >>>> off chance, if any one has some accessible instructions for the watch. >>>> I think I've broadly set it up correctly, but I'd welcome a helping hand >>>> from instructions or an owner of this item. >>>> Many thanks in advance. >>>> David >>>> >>>> >>>> Sent from my iPad** To leave the list, click on the immediately-following >>>> link:- >>>> ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe] >>>> ** If this link doesn't work then send a message to: >>>> ** access-uk-request@xxxxxxxxxxxxx >>>> ** and in the Subject line type >>>> ** unsubscribe >>>> ** For other list commands such as vacation mode, click on the >>>> ** immediately-following link:- >>>> ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq] >>>> ** or send a message, to >>>> ** access-uk-request@xxxxxxxxxxxxx with the Subject:- faq >>>> >>>> ** To leave the list, click on the immediately-following link:- >>>> ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe] >>>> ** If this link doesn't work then send a message to: >>>> ** access-uk-request@xxxxxxxxxxxxx >>>> ** and in the Subject line type >>>> ** unsubscribe >>>> ** For other list commands such as vacation mode, click on the >>>> ** immediately-following link:- >>>> ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq] >>>> ** or send a message, to >>>> ** access-uk-request@xxxxxxxxxxxxx with the Subject:- faq >>> >>> ** To leave the list, click on the immediately-following link:- >>> ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe] >>> ** If this link doesn't work then send a message to: >>> ** access-uk-request@xxxxxxxxxxxxx >>> ** and in the Subject line type >>> ** unsubscribe >>> ** For other list commands such as vacation mode, click on the >>> ** immediately-following link:- >>> ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq] >>> ** or send a message, to >>> ** access-uk-request@xxxxxxxxxxxxx with the Subject:- faq >> ** To leave the list, click on the immediately-following link:- >> ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe] >> ** If this link doesn't work then send a message to: >> ** access-uk-request@xxxxxxxxxxxxx >> ** and in the Subject line type >> ** unsubscribe >> ** For other list commands such as vacation mode, click on the >> ** immediately-following link:- >> ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq] >> ** or send a message, to >> ** access-uk-request@xxxxxxxxxxxxx with the Subject:- faq > > ** To leave the list, click on the immediately-following link:- > ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe] > ** If this link doesn't work then send a message to: > ** access-uk-request@xxxxxxxxxxxxx > ** and in the Subject line type > ** unsubscribe > ** For other list commands such as vacation mode, click on the > ** immediately-following link:- > ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq] > ** or send a message, to > ** access-uk-request@xxxxxxxxxxxxx with the Subject:- faq > ** To leave the list, click on the immediately-following link:- ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe] ** If this link doesn't work then send a message to: ** access-uk-request@xxxxxxxxxxxxx ** and in the Subject line type ** unsubscribe ** For other list commands such as vacation mode, click on the ** immediately-following link:- ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq] ** or send a message, to ** access-uk-request@xxxxxxxxxxxxx with the Subject:- faq