This makes no sense, if you have the Force manual for this model, HC9919C1, the alignment instructions should work. The model number is a hotel set, not a consumer set. ******************************************************************************************************************* Since 1972 Jim Myers Telrad Electronics Fort Wayne, Indiana Mouton's Electronics wrote: > Hotel units enabled in Force, how is this done? Is it something I have to do > or is that unlocked with the registration key they give you? Never noticed a > setting in Force itself. > > Jason > Mouton Electronics > New Iberia, LA > ----- Original Message ----- > From: "Phillip R. Hull" <phil245@xxxxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Thursday, November 18, 2004 1:12 PM > Subject: [TechAssist] Re: E8 chassis M# HC9919c125 Hotel/hosp set / service > mode > > > >> >>I used "menu "also and it does not work . There is a special remote to > > set > >>the hosp etc settings but it does not seem to set the geometry settings. > > If > >>you don't have the hotel units enabled in Force it does not give you any >>info for the Hosp. sets Thanks for trying, P.S. If I >>use 062596 menu or status the regular menu comes up. >>Phillip R Hull STET >>phil245@xxxxxxxxxxxxx >>FAX 517--569-3075 >>Professional Technicians only >>----- Original Message ----- >>From: "Mouton's Electronics" <moutons@xxxxxxxxxxxxxxxx> >>To: <techassist@xxxxxxxxxxxxx> >>Sent: Thursday, November 18, 2004 1:35 PM >>Subject: [TechAssist] Re: E8 chassis M# HC9919c125 Hotel/hosp set / > > service > >>mode >> >> >> >>>Phillip >>>I looked in my manual on force for that one and it says to use 062596 >> >>(menu) >> >>>and not (status) I know some use one and others use the other. Sometimes >>>there notes on alignments aren't accurate. I don't think this is one of >> >>the >> >>>models that require a special service mode remote but if it was it >> >>wouldn't >> >>>even tell you in the notes. I had to get Tritronics to do some research > > to > >>>get the number. >>> >>>Jason >>>Mouton Electronics >>>New Iberia, LA >>>----- Original Message ----- >>>From: "Phillip R. Hull" <phil245@xxxxxxxxxxxxx> >>>To: <techassist@xxxxxxxxxxxxx> >>>Sent: Thursday, November 18, 2004 11:25 AM >>>Subject: [TechAssist] E8 chassis M# HC9919c125 Hotel/hosp set / service >> >>mode >> >>> >>>>I can not get into the SAM mode to align the vert size. It must be > > a > >>>>different code than the regular one ( 062596 status) >>>>This combination does not work on these sets (I have six) does anyone >>> >>>know >>> >>>>how to get into the service mode on these hotel/hosp. units I have >> >>Force >> >>>>but not the Hotel/Hosp information >>>>Thanks >>>> >>>>Phillip R Hull STET >>>>phil245@xxxxxxxxxxxxx >>>>FAX 517--569-3075 >>>>Professional Technicians only >>>> >>>> >>>> >>> >>-------------------------------------------------------------------------- >> >>>--- >>> >>>>Lost Password: >>>>http://www.tech-assist.org and select "Login Problems?". >>>>Email Archives: >>>>//www.freelists.org/archives/techassist/ >>>> >>> >>> >>> >>-------------------------------------------------------------------------- >>--- >> >>>Lost Password: >>>http://www.tech-assist.org and select "Login Problems?". >>>Email Archives: >>>//www.freelists.org/archives/techassist/ >>> >>> >> >> >> >>-------------------------------------------------------------------------- > > --- > >>Lost Password: >>http://www.tech-assist.org and select "Login Problems?". >>Email Archives: >>//www.freelists.org/archives/techassist/ > > > > > ----------------------------------------------------------------------------- > Lost Password: > http://www.tech-assist.org and select "Login Problems?". > Email Archives: > //www.freelists.org/archives/techassist/ > ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/