[TechAssist] Re: Convergence Problem......
- From: "Bruce Tiedeman" <btied@xxxxxxxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Thu, 27 Sep 2001 09:08:12 -0400
Yes it is possible this customer had his hands in their. The adjustments
can't be corrected from the remote and are way off. I will check the
convergence panel etc, thank you.
Bruce.
----- Original Message -----
From: "Gonzalo N Arrivas" <gna2000@xxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Wednesday, September 26, 2001 9:08 PM
Subject: [TechAssist] Re: Convergence Problem......
>
> Bruce,
> You can access the convergence thru a remote control by pressing the
> menu/program button and make your adjustment selection. Sorry, I have the
> manual last year but I returned it to the customer. The customer may have
> done some convergence adjustments when the splitter was going bad. It
> happened to me and have to reconverge after I replace the HV splitter
block.
> Gonzalo N. Arrivas, CET Pittsburg, CA
> http://www.etechhelponline.com
> Tel/Fax: 925-432-2057
>
> If the Tech Site is Down. go to the below address to access.
> the following:
>
> Tech Message Board:
> http://members.sitegadgets.com/gnaenter8/board.html
>
> Electronics Tech Forum at SmartGroup:
> http://www.smartgroups.com/group/group.cfm?GID=255346
> ----- Original Message -----
> From: "Bruce Tiedeman" <btied@xxxxxxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Wednesday, September 26, 2001 5:39 PM
> Subject: [TechAssist] Convergence Problem......
>
>
> >
> > Rear Projection RCA .
> > PTK 169 PEC (P60752EB) 1995.
> > Replaced the HV. Splitter , now have a convergence problem. I was very
> > careful not to jar the C.R.T 's. I also made sure the leads where seated
> in
> > the splitter.
> >
> > I am at a disadvantage seeing the customer brought the unit to me for
> > repair. Regardless I have to fix the problem. Seems the R and blue
> > convergence will not adjust up to the green. It is about 1 inch out
> > horizontally.
> >
> > Is there a static adjustment for this condition or is it a yoke tilt
> > adjustment ? I have and old service manual from an older projection to
> refer
> > too.
> >
> > I need some advice on this , just don't want to get into making
> unnecessary
> > adjustments and possibly make it worse.
> >
> > I don't work on that many projection sets am not familiar with their
> > adjustments.
> >
> > Will have to go to the customers house to finish the job.
> >
> > thanks for any help on this,
> >
> > Bruce
> > B&T Electronics.
> >
> >
> >
> > Help make your TechAssist online repair tips
> > database better! Submit your fixes here:
> > http://www.circuitwork.com/techassist/tip/#tips
> > To unsubscribe write to:
> > techassist-request@xxxxxxxxxxxxx
> > with unsubscribe in the subject line.
> >
>
> Help make your TechAssist online repair tips
> database better! Submit your fixes here:
> http://www.circuitwork.com/techassist/tip/#tips
> To unsubscribe write to:
> techassist-request@xxxxxxxxxxxxx
> with unsubscribe in the subject line.
Help make your TechAssist online repair tips
database better! Submit your fixes here:
http://www.circuitwork.com/techassist/tip/#tips
To unsubscribe write to:
techassist-request@xxxxxxxxxxxxx
with unsubscribe in the subject line.
Other related posts:
