[TechAssist] Re: Convergence Problem......

There is another possibility, the connectors on the convergence board have
been known to corrode and cause intermittant shifting of the convergence.
There is a kit available from RCA to address this problem. Sorry, I don't
hve the kit number available.

Try wiggling the connectors and see if some shifting occurs, if so, get the
kit from RCA.

Good luck

----- Original Message -----
From: "Bruce Tiedeman" <btied@xxxxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Thursday, September 27, 2001 8:15 AM
Subject: [TechAssist] Re: Convergence Problem......


>
> My manual suggests this procedure thank you.. I have enough information
> sounds straight forward ....if there is such a thing.
>
> Bruce.
> B&T Electronics.
>
> ----- Original Message -----
> From: "Shoreline Electronics" <jstielau@xxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Wednesday, September 26, 2001 9:11 PM
> Subject: [TechAssist] Re: Convergence Problem......
>
>
> >
> > You have the static centering rings on each of the CRTS.  Make sure the
> > green is centered to begin with before you mess with the red & blue.
> >
> > Cover the red & blue lenses so you can see only the green.
> >
> > Then do Green & Red together...then add the blue.
> >
> > Jeff Stielau
> > Shoreline Electronics Repair
> > 125 Beechtree Lane
> > Westbrook,CT 06498
> > 860-399-1861 Voice
> > 860-664-3535 Fax
> > jstielau@xxxxxxxx
> >
> > ----- Original Message -----
> > From: "Bruce Tiedeman" <btied@xxxxxxxxxxxx>
> > To: <techassist@xxxxxxxxxxxxx>
> > Sent: Wednesday, September 26, 2001 8:39 PM
> > Subject: [TechAssist] Convergence Problem......
> >
> >
> > >
> > > Rear Projection RCA .
> > > PTK 169 PEC (P60752EB) 1995.
> > > Replaced the HV. Splitter , now have a convergence problem. I was very
> > > careful not to jar the C.R.T 's. I also made sure the leads where
seated
> > in
> > > the splitter.
> > >
> > > I am at a disadvantage seeing the customer brought the unit to me for
> > > repair. Regardless I have to fix the problem. Seems the R and blue
> > > convergence will not adjust up to the green. It is about 1 inch out
> > > horizontally.
> > >
> > > Is there a static adjustment for this condition or is it a yoke tilt
> > > adjustment ? I have and old service manual from an older projection to
> > refer
> > > too.
> > >
> > > I need some advice on this , just don't want to get into making
> > unnecessary
> > > adjustments and possibly make it worse.
> > >
> > > I don't work on that many projection sets am not familiar with their
> > > adjustments.
> > >
> > > Will have to go to the customers house to finish the job.
> > >
> > > thanks for any help on this,
> > >
> > > Bruce
> > > B&T Electronics.
> > >
> > >
> > >
> > > Help make your TechAssist online repair tips
> > > database better!  Submit your fixes here:
> > > http://www.circuitwork.com/techassist/tip/#tips
> > > To unsubscribe write to:
> > > techassist-request@xxxxxxxxxxxxx
> > > with  unsubscribe  in the subject line.
> > >
> >
> > Help make your TechAssist online repair tips
> > database better!  Submit your fixes here:
> > http://www.circuitwork.com/techassist/tip/#tips
> > To unsubscribe write to:
> > techassist-request@xxxxxxxxxxxxx
> > with  unsubscribe  in the subject line.
>
> Help make your TechAssist online repair tips
> database better!  Submit your fixes here:
> http://www.circuitwork.com/techassist/tip/#tips
> To unsubscribe write to:
> techassist-request@xxxxxxxxxxxxx
> with  unsubscribe  in the subject line.
>

Help make your TechAssist online repair tips 
database better!  Submit your fixes here: 
http://www.circuitwork.com/techassist/tip/#tips
To unsubscribe write to:
techassist-request@xxxxxxxxxxxxx 
with  unsubscribe  in the subject line.

Other related posts: