Hi Peter. Actually I brought this board to shop to work without tube. Just substitute the yoke.I even substitute the vertical signal driver at pin 4 I still have zero volt at pin 2 output.I will replace the diode and try TA8403.Thanks Dang TD electronics ----- Original Message ----- From: Peter oliver <oliver_peter1@xxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Thursday, January 16, 2003 7:20 PM Subject: [TechAssist] Re: vertical problem > > I saw one reference to that chip IX1224ce that said to use TA8403K. The data > sheet at B&D is in japaneese but this looks like the Tall vertical chip > sharp has used m in there mid 90's sets. on that basis the last one that I > had needed the vertical ic replaced, it still had voltage also there is a > cap (a 100uf I think) that fails or can fail near the IC and cause it to > fail I will try to send the data sheets I found to you (sorry I havent found > any in english). one is a PDF the other is a GIF file. Check the yoke and > see if the vertical ramp is being generated > > Peter Oliver > Tucson Radio TV > > > > From: "Gemini Computer & TV" <geminitv@xxxxxxxxxxxxxxxx> > Reply-To: techassist@xxxxxxxxxxxxx > To: <techassist@xxxxxxxxxxxxx> > Subject: [TechAssist] Re: vertical problem > Date: Thu, 16 Jan 2003 20:02:51 -0500 > > > Can you at least give us the size and approximate vintage? > > Bob Waterman, CET® #RI-28 > Master Technician License #9109 > Service Manager > Gemini Computer, TV, & Security Alarms > (508)695-7302 > (508)695-7769 FAX > geminitv@xxxxxxxxxxxxxxxx > geminitv@xxxxxxx > > ----- Original Message ----- > From: "Trac Dang" <t8872695@xxxxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Thursday, January 16, 2003 7:08 PM > Subject: [TechAssist] vertical problem > > > > > > Hello Group members. > > I am working with a Sharp TV (missing model #). No picture ,has > sound.Crank > > up > > screen voltage I see a horizontal line. There is no vert. Try every thing > > even replace Ic > > X1224CE to TA8427 I do not have original IC. It is a simple IC with 7 > pins > > I > > have 27 volts at pin 6 and pin3. Try hard but no luck. Any ideas is > > appriciated. > > Dang TD electronics. > > > > > > > > ------------------------------------------ > > Submit A Repair Tip For Everyone Here: > > http://www.tech-assist.org/secure/tip/main.html > > ------------------------------------------ > > To REMOVE your email address, click here: > > http://www.tech-assist.org/unsubb.html > > To CHANGE your email address, click here: > > http://www.techassist.net/forms/change.html > > > > > > ------------------------------------------ > Submit A Repair Tip For Everyone Here: > http://www.tech-assist.org/secure/tip/main.html > ------------------------------------------ > To REMOVE your email address, click here: > http://www.tech-assist.org/unsubb.html > To CHANGE your email address, click here: > http://www.techassist.net/forms/change.html > > > _________________________________________________________________ > Protect your PC - get McAfee.com VirusScan Online > http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963 > > ------------------------------------------ > Submit A Repair Tip For Everyone Here: > http://www.tech-assist.org/secure/tip/main.html > ------------------------------------------ > To REMOVE your email address, click here: > http://www.tech-assist.org/unsubb.html > To CHANGE your email address, click here: > http://www.techassist.net/forms/change.html > ------------------------------------------ Submit A Repair Tip For Everyone Here: http://www.tech-assist.org/secure/tip/main.html ------------------------------------------ To REMOVE your email address, click here: http://www.tech-assist.org/unsubb.html To CHANGE your email address, click here: http://www.techassist.net/forms/change.html