Looked same. I am thinking brake wear. Since you have to get in and out of these things to make a buck, I confess I did it this way.But my deck was,by far, better and almost new. His was worn visably. The customer is coming out better this way. Phil Bader al m wrote: >Did you check the gears for proper alignment on the bad one? If you had a >good one you should have seen something different. >Al Marquardt >ampm@xxxxxxx >Al Marquardt Electronic Repair >206 W Main >Girardville Pa. 17935 >----- Original Message ----- >From: "Phil Bader" <tjanphyl@xxxxxxxxxxxxxxx> >To: <techassist@xxxxxxxxxxxxx> >Sent: Tuesday, April 06, 2004 2:55 PM >Subject: [TechAssist] fix?: Symphonic (Funai) 13" TVCR SC3813. leaves a bit >of tape out when Ejected]]] > > > > >>-------- Original Message -------- >>Subject: fix: Symphonic (Funai) 13" TVCR SC3813. leaves a bit of tape >>out when Ejected]] >>Date: Tue, 06 Apr 2004 14:43:40 -0400 >>From: Phil Bader <tjanphyl@xxxxxxxxxxxxxxx> >>To: bull >> Greg Paradise <bulldog@xxxxxxxxxx> >> >> >> >> (OK I cheated...but the end justifies the means) >>FIX: step-by-step procedure: >>Put down your Doctor Pepper. >>Find a good Funai 13" TVCR from the back. >>(save the flyback...need that later!) >>Pull the almost new deck. >>Clean mode switch. >>Clean/lube mech. >>Swap salvaged good as new mech (with very low use) for the ****** up one. >>Test. Works. >>Set ****** up deck aside. >>With magic marker pen,on the old deck, clearly mark "***** up" for >>future use. >>Job done... >>;-) >>Phil >> >>-------- Original Message -------- >> >> >> >> >> >> >> >> >> >> >> >> >> >>-------- Original Message -------- >>Subject: Symphonic (Funai) 13" TVCR SC3813. leaves a bit of tape out >>when Ejected >>Date: Tue, 06 Apr 2004 13:41:37 -0400 >>From: Phil Bader <tjanphyl@xxxxxxxxxxxxxxx> >> >> >> >> >> >>Symphonic >>SC3813( 13 inch Funai made). Type with the single belt at rear. >>Orig. complaint was ate tapes,etc. I cleaned the deck, relubed, cleaned >>mode switch, reinstalled. Replaced two tactile switches in front (had >>corrosive on them). And checked/retimed mech. >>Now, Will accept tape, auto load, play, allthe mechanical functions OK. >>Push "stop" and "eject" and will do so, but just before the tape ejects, >> >> > > > >>it leaves a bit of tape out of the cassette to get snagged on something. >>Like it won't snap it in all the way. Just a bit. >>Suggestions? >>Phil Bader >> >>-- >> >>Philip Bader >>Jan Phyl TV Inc. (estab. 1976) >>3420 Recker Hwy. Winter Haven, Fl. 33880 >>Fax (863) 299-8821 >>email: tjanphyl@xxxxxxxxxxxxxxx >> >> >> >> >> >> >> >> >> >> >> >> >> >> >>-- >> >>Philip Bader >>Jan Phyl TV Inc. (estab. 1976) >>3420 Recker Hwy. Winter Haven, Fl. 33880 >>Fax (863) 299-8821 >>email: tjanphyl@xxxxxxxxxxxxxxx >> >> >> >>-------------------------------------------------------------------------- >> >> >--- > > >>Lost Password: >>http://www.tech-assist.org and select "Login Problems?". >>Email Archives: >>//www.freelists.org/archives/techassist/ >> >> >> >> > > > >----------------------------------------------------------------------------- >Lost Password: >http://www.tech-assist.org and select "Login Problems?". >Email Archives: >//www.freelists.org/archives/techassist/ > > > -- Philip Bader Jan Phyl TV Inc. (estab. 1976) 3420 Recker Hwy. Winter Haven, Fl. 33880 Fax (863) 299-8821 email: tjanphyl@xxxxxxxxxxxxxxx ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/