[TechAssist] Re: RCA ITC222 and chipper check//Crossover cable
- From: <tvservice@xxxxxxxxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Thu, 11 Mar 2004 17:24:36 -0600
This is a reply I got today about the cable for ITC222
The 222 chassis has a unique 2 row 10 pin connector. To connect the TECI 1
to this chassis you need a short adapter cable which is available from the
Sencore service parts department. The part number is 39G1095. The cost is
$9.95 Please call 1-800-736-2673 ext. 418 to order.
Regards,
Glen
Robert
tvservice@xxxxxxxxxxxxx
H & H Electronics Inc
Dallas, TX
----- Original Message -----
From: "Lakeside TV" <lakesidetv@xxxxxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Thursday, March 11, 2004 12:04 PM
Subject: [TechAssist] Re: RCA ITC222 and chipper check//Crossover cable
> Jason
> Apparently when we called Sencore and told them what chassis this was
for, at that time one cable was on backorder. Several days later the whole
kit arrived with pc board and 4 cables. You may want to give them a call.
>
> Bob Norcross
> Lakeside TV Service, Inc.
> Clinton Township, MI 48038
> Lakeside TV <lakesidetv@xxxxxxxxxxxxx> wrote:
> Fellow Techs,
> First sorry for the long post. Here's my experience with the ITC222. Set
came in dead. Would pulse three times at turn on. Ordered CCAB3686 TECI1
board and cables from Sencore. With the TECI1 board use the 7 to 10 pin
adapter cable that comes with it. Connect on the back of the set below the
RF connector where it says "for factory use only". Ran CC. Gave a Code 33 -
deflection safety circuit active or BV500 not connected. Basically, turns
out a pincushion problem (which will shut the set down) is the problem in
this case. Scoped pin cir. (called E-W)waveform severely distorted. All
components checked normal. Called RCA Tech line.Tech said "couldn't find the
cause of the problem, right?, We'll just give you an authorization # for the
board." Apparently they have been giving out a lot of these boards. Will
post final results when the board arrives.
> Bob Norcross
> Lakeside TV Service Inc.
> Clinton Township, MI 48038
> walter wood wrote:
> Yes, an eithernet crossover cable IS needed for the
> ATC311.
> But, what no one and no manual told us up front was
> there was another adapter needed for the
> convergence etc.
> Then, they admitted that the adaptor was needed,
> but that no one had built it yet.
> At this time, the sets were 12 to 18 months old.
> Sencore blames Thomson and Thomson blames Sencore.
> It finally was available about Oct. of 2003, and
> still did not work.
> I believe that this the same adaptor that you need
> to use on the ITC222.
> Apparently, they forgot to put a plug on the
> chassis for it.
> Good luck
> Walter
> By the way, we've dropped Thomson as a product to
> sell, and no longer do warranty work for them.
> Life's too short!!!
> --- Mouton's Electronics
> wrote:
> > Walter
> > I have used CC for some years and it works fine
> > for me. However I have not
> > used it on the ATC311. It uses a crossover cable
> > for the ethernet port. I do
> > remember all of the post on that one and it was a
> > topic of discussion when I
> > went to the Thomson ASC school back on Oct. They
> > insisted it worked and he
> > said he did several himself before leaving for
> > our meeting. I myself have
> > not had the opportunity to do it so I don't know
> > any of the potential
> > problems one would run into on that chassis.
> >
> > My problem has scattered info on it on there
> > website and CC users manual.
> > They don't seem to update it often enough or
> > carefully enough for a tech to
> > use the software proficiently.
> >
> > I just figure since so many people was having
> > trouble with this chassis
> > someone had to get a straight answer from Thomson
> > about on how to align it
> > with CC before I spend a whole day on the phone
> > with them. The call I made
> > today they wouldn't even let me stay on
> > hold....due to the volume of calls
> > they said call back later.
> >
> > Jason
> > Moutons Electronics
> >
> > ----- Original Message -----
> > From: "walter wood"
> > To:
> > Sent: Wednesday, March 10, 2004 10:21 PM
> > Subject: [TechAssist] Re: RCA ITC222 and chipper
> > check
> >
> >
> > > Jason;
> > > yours is the second request on this matter I've
> > > seen lately.
> > > I don't have an answer.
> > > I fought with Sencore and Thomson for 18 months
> > on
> > > the ATC311 chassis.
> > > The e-mails are all in the archives i'm sure.
> > > Truth is, I've never gotten Chipper Check to
> > work
> > > with anything!!!
> > > I've done all the up dates, and run all the
> > > diagnostics, and accordingly, it's working up
> > to
> > > specs.
> > > But, It doesn't work.
> > > Biggest waste of time and money I've ever seen.
> > > Just a thought, maybe it's speaking Chinese.
> > > Walter
> > > --- Mouton's Electronics
> >
> > > wrote:
> > > > Ok, Where is the big "mystery connection".
> > > > Chipper check say to use the MM101 TECI1
> > > > connector that I had to order from Sencore
> > but
> > > > since the CC doesn' t have complete setup
> > > > instructions to connect CC to the ITC222 I
> > have
> > > > no idea where to connect it to the chassis. I
> > > > have read others say they have changed the
> > SSB
> > > > board, so if you changed one I would hope you
> > > > used CC to download and reinstall the values
> > to
> > > > the new module. Or has everyone realigned
> > this
> > > > chassis manually, I hope not, that would be
> > > > painful;)
> > > > So, I would like to know if anyone knows
> > where
> > > > the connection is or has everyone been doing
> > it
> > > > manually? I will have to change the SSB board
> > on
> > > > one I am looking at now.
> > > >
> > > > Thanks in advance
> > > >
> > > > Jason
> > > > Mouton's Electronics
> > > >
> > > >
> > > >
> > > >
> > >
> >
> --------------------------------------------------------------------------
> > ---
> > > > Lost Password:
> > > > http://www.tech-assist.org and select "Login
> > > > Problems?".
> > > > Email Archives:
> > > > //www.freelists.org/archives/techassist/
> > >
> > >
> > > =====
> > > Walter Wood
> > > Future Tech Home Center
> > > 2786 Hwy. 43 N.
> > > Lawrenceburg Tn. 38464
> > > 931-829-3337
> > > Fax 931-829-4044
> > > mailto:wwood_38478@xxxxxxxxx
> > >
> > > __________________________________
> > > Do you Yahoo!?
> > > Yahoo! Search - Find what you're looking for
> > faster
> > > http://search.yahoo.com
> > >
> > >
> >
> --------------------------------------------------------------------------
> > ---
> > > Lost Password:
> > > http://www.tech-assist.org and select "Login
> > Problems?".
> > > Email Archives:
> > > //www.freelists.org/archives/techassist/
> > >
> >
> >
> >
> >
> --------------------------------------------------------------------------
---
> > Lost Password:
> > http://www.tech-assist.org and select "Login
> > Problems?".
> > Email Archives:
> > //www.freelists.org/archives/techassist/
>
>
> =====
> Walter Wood
> Future Tech Home Center
> 2786 Hwy. 43 N.
> Lawrenceburg Tn. 38464
> 931-829-3337
> Fax 931-829-4044
> mailto:wwood_38478@xxxxxxxxx
>
> __________________________________
> Do you Yahoo!?
> Yahoo! Search - Find what you're looking for faster
> http://search.yahoo.com
>
> --------------------------------------------------------------------------
---
> Lost Password:
> http://www.tech-assist.org and select "Login Problems?".
> Email Archives:
> //www.freelists.org/archives/techassist/
>
>
> --------------------------------------------------------------------------
---
> Lost Password:
> http://www.tech-assist.org and select "Login Problems?".
> Email Archives:
> //www.freelists.org/archives/techassist/
>
>
> --------------------------------------------------------------------------
---
> Lost Password:
> http://www.tech-assist.org and select "Login Problems?".
> Email Archives:
> //www.freelists.org/archives/techassist/
>
-----------------------------------------------------------------------------
Lost Password:
http://www.tech-assist.org and select "Login Problems?".
Email Archives:
//www.freelists.org/archives/techassist/
Other related posts:
